Search:

Steering cylinder position sits 50% of the time in the middle and on either end the other 25%. I’ve done it this way as told to. Maybe not the best way but that’s what I’ve been doing.

Also tried...

Thanks for the responses. I’ve got better seals from a hydraulic shop, not Teleflex brand, but was concerned about tearing up the glands or new seals trying to get the old out and new in. Did the...

Good morning. I’ve got an HC 5345 Seastar steering system on my Triton TR186 Boat. I changed the seals last year with a new seal kit that included the glands and seals, I added new fluid, bled the...

Reelcrazy - that’s what I was thinking too initially but that piece is fully intact. At times it doesn’t line up so I’ll use quick fix by doing what you said which is to spin it and it locks in. ...

Thanks Bradrodfish for trying to help. I’m lost too and that was why I was posting.

Thinking through this is might not be the shaft rotating rather it may be the part in the steering module...

Ok, here’s a couple of photos as requested. Looks like that output sleeve is intact and the engagement dog bar is working too. I thought that sleeve might have been the issue on my initial post but...

If you look at the 3rd photo this is where I can see it spinning where that little bit of grease appears to the right of the engagement dog that fits into the liner tube output that sits on the...

Here’s 3 photos. 526511526512526513

Bradrodfish, sorry that I wasn’t clear so let me clarify. After the motor is first deployed I’ll press the left or right button on the remote to line up the head where I want it to go. Then hit the...

Thanks Bradrodfish. I was hoping it was something super simple like the screw you mentioned. Unfortunately, I checked it and the screw that bolts the head on is fully intact and the locknut is also...

I've got a 2018 Bluetooth Terrova 24v motor. Was out last week and had some issues where I can see the shaft spin but the head doesn't move. Using the I-pilot link remote I can press left or right...

Glad some of the info seemed to help. I’d suggest that you double check that they got the seats tight when they put them back in.

Also, I’ve heard of the permeation issues and have it at times...

So I’ve got the exact same seats in the same boat. I’ve taken my seats out a couple of times to clean them up and the area that they sit on when it was really dirty and when I replaced the carpet...

Thanks all. Much like I expected. Now out looking for a new one taking Don’s advice for OEM if I can find one.

2013 Fourstroke 150hp serial 1B945500. Out the last couple of days for just a few hours each day. Noticed later on during first day that I would get a low voltage notice on Hummingbirds and came...

Finally took it on and it was super easy. I used some puppy training pads to protect the carpet and clean up was easy too. Thanks to each of you for your help here. THANKS!

Got it. Thanks guys!

Thanks. I think I get what you are saying. I don’t mind using more fluid if needed to get it bled right. One question, the 12 foot tube from the “T” connector goes “back to the SeaStar fill bottle on...

Went out to try the marine tech bleeder again today and with suggestions above I was able to make progress getting more fluid into the system. Turning the wheel slowly each direction seemed to be...

I wish mine had worked like yours had. Did it the same way but guessing I way too much air in the system so far. Likely will have to use a hybrid of both processes.

Port side cylinder seal leaking so I decided to take the time to flush the system, fix the seal, then refill everything. Flush seemed to go fine and the seal replacement was much easier than expected...

Thanks for your advice and the links above. Will try it out.

Thanks Rojoguio. I’ve seen several of these and some video where people didn’t take their time as you suggest. Based on your input I’m going to try this and do it in the least visible place. Any...

Wish I could have that person “step up” but he passed in February. He always took me out fishing and his boat was set where he put his rods in the center and he just did things very much the same...

Just finishing up a full carpet replacement and starting to put things back in place. I knew I had some holes in one of my vinyl seats (middle seat in cockpit of my Triton TR186) and thought about...