Anyone fished this lake lately, and with the water low like it is where can you safely launch on the lake? Also, only areas south of Pendleton bridge.
Type: Posts; User: Golfinca
Anyone fished this lake lately, and with the water low like it is where can you safely launch on the lake? Also, only areas south of Pendleton bridge.
Only had to replace the front panel had a guy use sheet metal and he painted it, cut proper holes and came out pretty good.
Ditto what tzx200 answered
07 200 hpdi.
If you go to toledobend the guy at midland marine changed mine and actually used the mercury trim relay on my hpdi. Two fuses one for up and one for down. If a fuse goes out you can swap to the...
Pm sent
Does anyone nowhere I can get my abs module on my 2009 f150 lariat repaired in LA. If not where I may be able to find a working used one?
I have the same motor and I also think it is the cowling. No performance issues.
I was going to use the same rubber it's good shape. Could be part of my problem it has old glue residue. I think I'm gonna try the 3m stuff and if it doesn't hold then I will look into replacing...
What is the best adhesive to use on the rubber lining for storage and rod boxes?
Shafts can be worn down allowing the thrust washer to go to far up the shaft. If that is the case the shaft will need to be replaced. If not replaced you can tear up the lower unit bearing housing...
Congratulations looks nice. Give us. Some performance numbers once you take her out.
I have been where you are now.Started with a m25 2 3/4 inch below the pad and my 190 would start to violently chine walk at 65 mph, went higher and would start chine walking earlier .That is what...
Has anyone bought any electronics from shopepal.com and so what was your experience.
Ok I will give it a try charlie206 thanx!
I have a 2007 3.3l vmax hpdi that at 5800 rpm cuts out and goes down to approx 5400 rpm for 30 seconds and the starts climbing until it hits 5800. I changed the primer bulb,spark plugs and fuel...
I have a 2007 190 with 200 hpdi and have run a 25m yamaha prop and a 25p power tech vmx (t-1) clone. From input from other forums members for hpdi motors t-1 or their clones or the props for that...
Just changed prop on motor and raised jack plate to even with pad on a 190 prov blazer. Running a power tech vmx 25p and when I get to 5800 rpm on my digital gauge the motor drops rpm back down to...
Mine is on a 1200lb blazer cruise a lot between 4300 rpm and 5200 rpm and I use mercury premium plus tcw3 from Walmart $19.00 a gallon. Also no ethanol currently $3.09 a gallon where I live. I want...
I don't believe series 2 started till later but I have a 2007 200hp hpdi I bought last year with 107 hours. Changed the water pump and cleaned the popit valve due to temperature issues, other than...
Thanks to Bob and company another satisfied customer. I left State Farm insurance and went to these guys. Better rates and more coverage and a thorough explanation of the policy and how it covers...
No doubt right now I like riding vs fishing better. That boat is fun to drive on the tight river by the house. Yea I know speed can be addictive but where does it all stop 80 mph, 90 mph, 100 mph? ...
Ok thanks for all the advice I will take my time(safety first) plus I have never caught any fish while going 70 mph!!!!!!!!!!!!!!!!
Dont know what max rpm's are because they are still climbing when the boat starts severely listing side to side so I let off power and trim down to get the boat under control. When I bought the boat...
Blaznbyu boat currently setup 1" below pad on can lower 1/4" or 1/2" and then I'm at the bottom. Read your post and started researching the t1, I think I will try to find me a used one and try...
Also the has a 15 inch hydrodynamics jack plate and the nose cone to pad distance is 31 inches is this to much setback.