I added a atlas micro jacker to my landau mv1650. Running a 90hp two stroke Yamaha. It is awesome for shallow water I can get up in almost no water. Top end on mine didn’t really change much. I did...
Type: Posts; User: Skeeter00185
I added a atlas micro jacker to my landau mv1650. Running a 90hp two stroke Yamaha. It is awesome for shallow water I can get up in almost no water. Top end on mine didn’t really change much. I did...
I found when I have my motor trimmed down in the garage there is fluid slowly leaking out around the trim rod seals. I ordered two new seals to go in the caps, and two new o rings as well as some...
Thanks for the reply, what is optimum compression on these? I only ask because usually I see closer to 120 when I see them pop up and both my current two strokes have 120-125.
I am looking into purchasing a 2007 Yamaha two stroke outboard. The compression was tested while motor was warm and it tested 90 on all three. The guy is using a cheap gauge so don’t know if that...
I need a little help from the experts. Been chasing a problem with my motor for a while. The symptom is when accelerating it stops at 4200rpms and then all of sudden without touching the throttle it...
So I have had my 80lb thrust ultrex for 3 and half years. About a year and a half ago it got really wobbly and creaky and I discovered the little plastic pivot bushings had cracked and broke. I...
I can’t say for certain what your motor should do, however on my 1999 vmax only the oil light lights up for a few second when you turn the key, my overhead has never come on.
I appreciate the response, I got that o ring aswell. That one is like 4 times the size of the one I’m talking about
I know this is a much smaller motor than most on here. But I got a 2003 Johnson 15hp. Model number j15rstd. I ordered a water pump kit for it.when removing lower unit a small o ring fell out from...
I am going to look at a 1992 mariner 25hp. The motor does not run, seller says it needs a new stator. It is really cheap and I doubt I would lose any money if I can’t get it to run, but I am curious,...
Do you have a phone number or email I can send to? I don’t know how to post pictures on here
I’m in wake Forest, it’s a landau 16ft side console.
I am in search of a welder to fix an aluminum boat I have. The supports that run across the boat have a bunch of cracks in the welds, can anybody recommend someone to fix this?
thanks
I recently discovered a cracked weld on my landau mv1650. I am wondering how big of a deal this is and if it needs to be repaired or not. The boat does not leak. The crack is under the front deck...
I am having another problem with my 50hp Yamaha. It is a 1997 50tlrv. Finally got it to idle good, and run great on top end. Only thing wrong, whenever I cold start it, it will let out a loud high...
Sorry, forgot to include that, it has a 1997 50hp precision blend Yamaha on it.
I have a 16.5 side console aluminum boats. It is very light. The prop I have now is in bad shape with a dime size chunk missing on one blade and lots of dings. It is a 12-1/4 9 pitch. The boat runs...
I have a 1997 50tlrv Yamaha. It idles good on the hose, but it seems to only be idling on one or two cylinders. Is this motor designed that way or is it supposed to idle on all three? If I unplug top...
Thanks for the reply. I can move the splines on the lower unit but can’t find neutral. That’s my problem. No matter where I adjust it the prop always spins the drive shaft with it
I am trying to put the lower unit back on my 1997 50tlrv. I had a lot do trouble getting back on and it would stop 3/4 inch from going on. I twisted the splines to the shifter on the lower unit and...
I recently bought a trailer for my jon boat and it needs new hubs. The spindle requires 3/4 inch bearings, I can’t seem to find anywhere I can get a hub to fit a 3/4 inch spindle. Does anybody know...
I am in wake Forest, but willing to drive a bit to get it done. Unfortunately I already tried to drill out one and broke off and extractor inside one of them.
I have a 50hp Yamaha that I tried to remove the water jacket on, wound up breaking 9/14 bolts and need them drilled out. Anybody know a good machine shop to take it to get this done?
I recently bought a 1997 Yamaha 50tlrv and was trying to remover the cover over the water jacket. The first two bolts broke and I stopped after that, but I’m guessing more will if I keep going. I...
I just replaced both hubs on an ezloader trailer for my aluminum boat. I bought a kit with hubs, seals, cotter pins, and bearings. When I did the second one I noticed there is a gap from the seal and...