Search:

I have tried so many of these decal removers, and have been disappointed by most, but this 3M Adhesive eraser wheel was by far the best, and fastest for me. It's not cheap, but for someone with...

Hello Lea, hope you are getting better, I am on my way to a meeting, so I have to rush, anyway, I have a 1989 201, that I bought as a basket case, and I had to rewire everything, and re plumb...

Hello everyone, I am just updating my post, because I thought my problem was fixed, I was not happy with the speed I was getting, and I thought I was noticing some misfiring at lower rpms, so I...

GT knot, was proven the strongest knot by the IGFA, beat all variations of the alberto knot, and the FG knot, way easier to tie

https://youtu.be/TASzTlhfouY

Hello, I would like to offer up my two cents about the Ultrex, they hang over the bow quite a bit, just like the Xi5, that I put on my 201, and what can happen is the trolling motor can hit the...

thanks guys for your help, this motor has only one plug per cylinder, and it is a 1.857 gear ratio, (26/14), I believe it came from N.Y. , Brooks Cove Marina. then somehow ended up in Conn. where I...

Hi everyone, I posted this question in the Champion owners group forum also, but here is my question, my prop to pad is 3 1/2", I have a hydraulic jack plate, which is new to me, never had one...

Thanks 86 inches, a 25p tempest? even though I tried 22P suzuki prop, I lost speed and rpms at wot with it, do different brands make that much of a difference? I have heard Mercury prop can be used...

Hi everyone, I have a 1989 201, which has been repowered, with a Suzuki DT 200, I now they only came with Mecury, or Jhonson, so im trying to find out what type of speed I should expect in this boat,...

You can bypass the fuel tank completely, by using a gas can, just to run it, but I would not try to start it until you go through the fuel lines and clean those tanks with K100. I just went through...

418084418085418086
here is the part that I replaced, it's job is to keep the throttle from lagging behind when you punch it, at lower RPM's and a picture of my boat for good measure. Thanks...

Hello everyone,
I have finally figured out my problem on this motor, it was the throttle valve switch. I read about it in my service manual, and did an electrical test on page 57 and the unit...

yes billnorman1, this is a V6, the plug gap in my manual gives a range of .035 to .039, anyway, I sent out the 20p prop, and tried to use the 18p prop while my prop was getting fixed, it would not...

I have been kicking around the same idea, because my original, T.I. trailer needs so much work, and I would prefer tandem axle, to my original single axle, and I noticed that EZ Loader trailers...

first of all, thank you very much for everyone's help here, what a great resource this is. Thanks booter, I will definitely run the sea foam tomorrow. Okay, so this morning, I actually gapped the...

Hi all, just an update, I removed the spark plugs, and they were pretty wet, and fouled, and I found they were not gaped properly, they were to tight, the manual gives a range of .035 to .039, so I...

Thanks for the help billnorman1, I will keep investigating, until I figure this thing out!

Thanks for your help booster, I will double check tomorrow for a kinked fuel line, although I have replaced all of them on both tanks, and I have checked my spark plugs and actually replaced them...

Hi, hoping someone might be able to help me out, bought a 1989 Champion bass boat, that had been repowered with this 1986 DT200 motor three years ago, had been sitting for three years, I have been...

I have had good luck with Precision Sonar for bow and console mounts for my 201

https://www.precisionsonar.com/products

Thanks 86 but I already ordered it so we will see, I bought this boat knowing that it needed a ton of work, been working on it since last February, and It’s just one more thing on my long list....

On my 201, my fill switch is a three position on, off, on, and only has three blades, power goes to the middle blade, and powers either the up or down position. I don’t think the switch having extre...

So today I installed the new motor but it only has two wires, up and down, no negative wire so I guess I need the relay harness with this motor, I’m just going to order it and see.

http://www.bbcboards.net/attachment.php?attachmentid=331815&stc=1
So I finally figured out how to resize pictures from my phone, and here is the picture of my motor, ...

I pretty much gutted the bilge and livewell, all new flow-rite fittings and hoses, pumps, wires and fuses and switches, then fuel lines and fill and vents, I also when I changed the drain valve I...