Thank you. Looks like I'll be sending this one back.
Type: Posts; User: JCJ
Thank you. Looks like I'll be sending this one back.
Thank you.
Thank you. These won't even start to thread-in though. They almost seem to be the same size threaded holes as where the small plugs go on each side of the adapter plate. I was thinking about running...
1999 200 Opti (ser. #0G886121)
Replacing the exhaust plate gasket. Wondering what prep work I need to do besides cleaning the old gasket material off. I've heard on the gasket for the powerhead,...
1999 200 Optimax (ser. #0G886121)
I damaged my exhaust adapter plate recently, and purchased a new OEM one from Mercury. When I recieved it, it had a package of new fittings, and the rubber outer...
Thanks Don. When I got everything apart, I did find the seal on top, and o-ring on bottom. In your experience, would you expect these seals to go in fairly easily? The reason I ask is because I did...
1999 200 Opti (Ser. # 0G886121):
Wondering if anyone out there has any experience with installing a new swivel pin seal? Not sure what I'm doing wrong, but it's awful tight (like to tight) to...
Thanks Ya'll. Appreciate it.
1999 200 Opti (ser# 0G886121)
Hey everyone. I'm working on an over temp issue that's happening when my motor idles for extended periods. I removed and cleaned a strainer that's located on the...
Appreciate it. I'll double check the pump and see if I see anything out of whack. I did see the thermostats cycle, so believe they're ok. Any ideas on why the #1 and #3 cylinders would be running...
1999 200 Optimax (Ser. #0G886121) -
Been fishing an area that requires extensive idling due to high water. Noticed that when I'm idling for more than say 15 - 20 minutes, I'll get a continuous...
I did a hard reset on my Carbon 12 yesterday, hoping that it would resolve my AT1 freezing and saying "no source". Unfortunately, it did not help me. Within an hour, mine did it again.
Appreciate this, but hate to hear it. I think I'll write Lowrance and see if I can at least get a case started with the specific problem, since this is the same as what was happening with mine after...
Perfect - thank you!
I know many folks were experiencing their AT's freezing up, or going black when using 360 scan. Anyone know if the new 23.3 update resolved that issue? I've always had an AT1 and Carbon 12 unit, tied...
I'm seeing the same after the update. If I select only the AT display, it uses the full screen. However, if I split it, it shrinks it down the AT (top and bottom). My unit is an AT1 system.
I installed the new updates on my Carbon unit, and AT1 this morning. The Carbon update went fine, but I noticed when I went to install the AT1 update and selected the 23.3 update from my storage, it...
This is exactly what I was thinking when I purchased it, and happens to me --- "I'll 360 and find something interesting, then switch back to the AT....nope, damn graph will lock up or won't let AT...
Basshopper...
I bought the AI 3-1 nosecone for the Ghost (not using a separate 3-1 transducer). This is what I'm going to go return since I really can't use the 360 without the AT screwing up,...
Hey ya'll....
Just wanted to jump in here and pass on some information I received back from Lowrance this week regarding my AT going blank. To start with, I've had a Carbon 12 unit and an...
Yes. I did pull it completely out to look at it, but it came out easily and seemed to go back in easily (and to the same position prior to me pulling it out).
1999 200 Optimax (ser. #0G886121) -- Replacing water pump, and have a couple of questions about the shift shaft. There's a rubber washer that sits on top of the shift shaft housing seal. I've heard...
Hey everyone...
Just wanted to post a quick reply that I finally got this issue figured out. It ended up being my CDI module. Apparently the oil control unit is integrated inside the CDI, and...
Thank you. With the #2 and #5 cylinder not firing, does that sound like the motor is operating in rpm reduction mode to you? I haven't really confirmed I'm in rpm reduction mode, and kind of just...
Hey ya'll... I have a 1997 200 Yamaha SW series motor on my Skeeter and hoping someone can help me figure out a problem I'm having.
Had the boat out the other week, and while running WOT, all of...