Search:

So i will start by saying i do not have a photo of the tire tread wear pattern and i just bought new tires last week so i cant get photos any longer:doh: but i will explain what is happening and...

I did some research and i could not find a straight answer and thought i would ask the question here. i did reach out to Minkota as well but i haven't received a response yet and i would assume they...

Might have figured it out. When I removed the old motor it had the three wires and when I reinstalled the black and red I didn't tighten down the loose connection where the white wire was located and...

Wiring gremlins got me I believe. Still having issues. I also found the 12-24v plug was melted slightly when I looked at the connections.

So I was was able to get out and do some testing this morning and determined the breaker only has 12v on one side. So now I need to replace the breaker. Both batteries have breakers and per Minnkota...

I do have 4 wires at the bow behind where the plug is located. My original motor had a red wire black wire and white wire so when I rewired the plug i put the new red and black wires where the old...

Hey everyone so I recently installed a new Minnkota Foretrex 80# on the from of the boat. I have used it 3 times in the last couple weeks since I have installed it and it has worked flawlessly. This...

I am looking into getting the thru hull transducer and y cable and maybe mounting the side imaging transducer above the pad area where the notch is located that has the drain and pickup lines for the...

Does anyone have any advice on where I should mount the Side Imaging Transducer on the transom? Photos would help. Thanks. i also have the Stern Saver mount that needs to be epoxied to the transom...

Well I got the new 10" Humminbird SI unit and will be looking at having a custom mount made so I can keep it in front of me instead of mounting it on the side. My boat doesn't have the side rail and...

Well i decided to go with the 10". Now i just have to figure out how to mount it. mrdeath, what 2d transducer did you buy for the bilge area? Did you need to get a splitter cable too?

Thanks for the photos. I have thought about downsizing to a 7" and having a bracket made as well but i was curious to see if anyone had some good ideas first. By the way how does the side imaging...

Hi everyone I am looking at getting a new Humminbird Helix 10" unit and I would like to install it at the console, preferably directly in front of me and replace the existing one I have that is shown...

I also have a 2001 Cobra and no leaks so far. it gets topped off occasionally as well

Update: I ended up taking it to a local shop and they cleaned out the on board tank and hose lines and put it back together. The tank on the motor is now being refilled with oil however the sensor...

So while I was out on the water yesterday driving the boat my Smartcraft gauge started beeping at me blinking the oil indicator and check engine. Since I have only had the boat for a few months now...

Ok. Thanks for the response, I will check that out too

Ok. Thanks for the response, I will check that out too

I did a search using the numbers on the side of the shock and I found similar ones that are the same length. I will order some and update the thread.

Thanks mrdeath, I doubt it will make much difference either but it might start to wear on the mounting points, mainly why I asked to see if someone would recommend against it or knew of a direct...

Still getting acclimated to the new boat and I have noticed the storage lid shocks are wore out and they only hold the lids open if you push them all the way open and even then they tend to want to...

Thanks for the info. My next trip out I will review it further.

Good morning all. Took the boat out for the first time this weekend for a club tournament and the boat ran pretty good. Top speed on the speedo was about 57 MPH, next time out I will check it with...

Yes I did thank you. I had sent you an email response as well. Hopefully I will start that project soon. Still need to get a tray though

Thanks to all for the comments and advice.