Sorry I'm at work and don't have the serial number on me. Motor is 2019 150 4-stroke. Current prop is Quicksilver QA2008x.
Looking for Quicksilver Qs5050x 14.5"x 15 pitch or equal.
Type: Posts; User: mitchell301
Sorry I'm at work and don't have the serial number on me. Motor is 2019 150 4-stroke. Current prop is Quicksilver QA2008x.
Looking for Quicksilver Qs5050x 14.5"x 15 pitch or equal.
I am looking for SS 14.5" x 15 pitch prop for my pontoon boat. They are backordered everywhere I have tried. Looking for suggestion of a place that might have one. Thanks
Thanks Wayne. Gonna order it now. I like the mount better also.
I just got a helix 7 chirp si g2n and have began installing it. I was having trouble get the transducer mount to fit on the step of my ranger where i had the previous transducer. In searching for...
Thanks for all the input/ideas guys. I got it off today and shear pin has been replaced. I used a combination of ideas to get the plastic nut off.
I used a small soldering iron and heated up the...
Is that nut all plastic with no metal nut embedded? If so I reckon I can carefully cut it trying to not damage the shaft threads.
This nut is the plastic winged type nut. To make matters worse, I think I recall when I put this prop on I put a dab of Locktite on the threads.
It appears that my shear pin is broke. I cant get the nut that holds the prop to the shaft to come loose, the shaft turns with it. Is there a trick to holding the shaft while turning the nut? Are the...
Thanks for input. I'll clean it up and give it a try, hopefully this week. I also was running a little extra oil in the fuel because of the age of the motor and that may have contributed to it....
I don't think that I flooded it. When I first put it in the water this year, I had to pull the crank several times then I had to re-pump the bulb before it would fire off. I figured it was just...
I have a '68 Johnson 20 (FD-20a) that has not been used much in the past 15 years or so. I have rebuilt the carb, replaced impeller and have been using it some lately. I have noticed oil dripping out...
Thinks for the input...i will give Champion a call. Do they ship relatively quick?
I have a 92 Ranger with a single axle trailer. Last night my son was pulling it to his house so he could fish a tournament this morning and as he pulled up his driveway the axle broke on the right...
I have a very similar chip in the hull of my Ranger. I assume that y'all are talking about the Marine-Tex epoxy putty? Would any other epoxy work or maybe J-B Weld ? and where do you buy Marine-Tex,...
thanks...that did it...
thanks..how do you get to this screw? do you have to unscrew the cast adjustment?
I am trying to take apart my Daiwa to clean and lube and I'm having trouble getting the right side gear plate off. I have the screws out and it will pull out part of the way but something is holding...
LN...thanks for the info !!! I really like looking through your collection of brochures and photos !!! Thanks for posting them.
I have an older Evinrude 6 hp that belonged to my Dad. It only has a serial number plate on it. My other older E-J's indicate model number and serial number. The serial number it 6902M-E01322. Would...
http://www.tommyheadjigs.com/
my favorite...
I would like to hear suggestions on this one too. I have a 20HP (FD-22A) that I have to pull choke partially out to run. I have rebuilt carb, but not sure if float is adjusted properly.
Bass...thanks for the reply. Got a couple re-build kits.
Anyone have comments on t'stat possibility??? and difficulty??
I have a 1979 Johnson 55HP that doesn't get used much and it wont idle unless I keep th efast idle lever about 1/3 up. And of course like that it wont go in gear. It dies even after running it on...
Yeah, I know. I was just wondering why 5 days after the new injectors were installed that the programming had not been done. I reckon that they were just backed up with work. But all is fine now. ...
Thanks