Search:

Type: Posts; User: Team Colibri

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    32

    Check under «Sonar» in the list.

    Check under «Sonar» in the list.
  2. Replies
    3
    Views
    44

    Network them with WIFI as described in the units...

    Network them with WIFI as described in the units manual, and they will synch waypoints between them.
  3. Replies
    9
    Views
    143

    If the HDS Touch is a Carbon/ Live Pro, the...

    If the HDS Touch is a Carbon/ Live Pro, the connectors are the same as for your Ti and you can test by just swapping units around. If it is a HDS Gen 2 Touch or Gen 3, the transducer-port is...
  4. Replies
    4
    Views
    130

    If the map-card is in your other unit, that...

    If the map-card is in your other unit, that message popping up a lot will typically mean your ethernetcable is about to go belly up.
  5. Replies
    3
    Views
    149

    Navionics as chart-source is available even with...

    Navionics as chart-source is available even with no card. Your issue is typically related to a dying ethernetcable, but test the card in the other unit as well.
  6. Replies
    5
    Views
    77

    Reefmaster is not compatible with anything that...

    Reefmaster is not compatible with anything that has an Apple on it.
  7. Replies
    5
    Views
    77

    Reefmaster is fairly cheap, and so much better...

    Reefmaster is fairly cheap, and so much better than the alternatives, that I see no reason to even look at alternatives.
  8. Save waypoints, do a hard reset.

    Save waypoints, do a hard reset.
  9. Thread: Fuse size

    by Team Colibri
    Replies
    3
    Views
    84

    Minimum size is 3A, actual size is given by the...

    Minimum size is 3A, actual size is given by the wiring you use. In short, 3A or more.
  10. Replies
    7
    Views
    224

    1. I prefer SS3D over all other alternatives. 2....

    1. I prefer SS3D over all other alternatives.
    2. Yes, just ensure the Gen 3 is fully updated and it will network will with newer units.
  11. Thanks rob!

    Thanks rob!
  12. What are the issues? (I don`t have a 150 anymore,...

    What are the issues? (I don`t have a 150 anymore, I sold it when I bought my 185HW.)
  13. Assuming that you mean AI 3i1, and that the...

    Assuming that you mean AI 3i1, and that the transducer is connected to the correct port (channel 2, called «structure» at the back of the unit), the transducer should be automatically recognized. Go...
  14. If you swap places for the units, your Carbon is...

    If you swap places for the units, your Carbon is compatible with AI, the Gen 3 is not.
  15. Replies
    2
    Views
    104

    Why not just export them from Reefmaster?

    Why not just export them from Reefmaster?
  16. Restore sonar-defaults and set it up again.

    Restore sonar-defaults and set it up again.
  17. Replies
    4
    Views
    105

    Yes. Even to non-Lowrance units, as most of the...

    Yes. Even to non-Lowrance units, as most of the NMEA-sentences used are generic.
  18. Replies
    9
    Views
    143

    1. Test with another (know good) transducer. 2....

    1. Test with another (know good) transducer.
    2. Save waypoints and do a hard reset.
  19. Replies
    1
    Views
    102

    It is on 9 vs 9, so I would expect it to be on 7...

    It is on 9 vs 9, so I would expect it to be on 7 vs 7 as well.
  20. Replies
    7
    Views
    249

    Lowrance units showing incorrect suply-voltage is...

    Lowrance units showing incorrect suply-voltage is by no means normal, issues in electrical systems causing voltage drop is VERY normal. As long as your units have updated software, you can safely...
  21. You should never assume that anything not mounted...

    You should never assume that anything not mounted by you is mounted like it should. :) Especially when it comes to headingsensors (like your P1) and transducers, as mounting this perfectly requires...
  22. Replies
    5
    Views
    122

    Your SS 3D module connects to your unit with...

    Your SS 3D module connects to your unit with ethernet, the yellow-ish connector on your unit. I have no idea what you mean by power wire to the structure inlet, you should not have anything...
  23. Replies
    3
    Views
    83

    As Gen 3 can only handle one 2D-transducer, I’m...

    As Gen 3 can only handle one 2D-transducer, I’m going to guess that your TotalScan is really an LSS-2. :) If it is not, you can simply use the 2D from your TotalScan by selecting m/h TotalScan as...
  24. Minor updates will never be available through...

    Minor updates will never be available through WIFI, only the major ones.
    Some updates require a large update-file, those will not load over WIFI unless you have a memorycard in the unit for storing...
  25. Replies
    5
    Views
    174

    I have VV Link in combination with various units,...

    I have VV Link in combination with various units, but I have never looked for water-pressure. I`ll check the next time I`m on the water.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4