Search:

Type: Posts; User: ChrisCarsonMarine

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Call me,305-394-3354,Chris

    Call me,305-394-3354,Chris
  2. Your motor has 3 triggers in the trigger...

    Your motor has 3 triggers in the trigger assy.They each fire 2 cylinders,1/4,3/6,and 5/2.Very likely you have a bad trigger,and this is how it would present,Chris
  3. Replies
    18
    Views
    623

    Don caught me🥹,.005 interference,not clearance…I...

    Don caught me🥹,.005 interference,not clearance…I need to proofread,Chris
  4. Replies
    18
    Views
    623

    Factory interferance is .002-.0025,and is...

    Factory interferance is .002-.0025,and is sufficient as long as the motor dose'nt suffer an overheat,as that interferance is gone at 200-250 degrees.We install oversize sleeves at .005...
  5. Replies
    18
    Views
    623

    If the sleeve got loose enough to turn,pinning it...

    If the sleeve got loose enough to turn,pinning it in place will heep it from turning,but it won't keep carbon from infiltrating the gap between the sleeve and register.This will result in a thermal...
  6. Replies
    13
    Views
    452

    Definately change the reeds to composite,they...

    Definately change the reeds to composite,they often chip and break,sad to hurt a piston with a broken steel reed.We make good reeds and crankcase stuffers for your motor,Chris
  7. Replies
    16
    Views
    508

    Have you checked to see if a sleeve has turned...

    Have you checked to see if a sleeve has turned ?,not uncommon on an O ring head motor,Chris
  8. Lots of circumstances slowed us down,but were...

    Lots of circumstances slowed us down,but were catching up...dont understand why I'm not getting calls,try my cell,305-394-3354,Chris
  9. Replies
    12
    Views
    433

    I don't believe factory oversize are...

    I don't believe factory oversize are available,but we have great aftermarklet ,Chris
  10. Replies
    7
    Views
    213

    Dry,No sealer needed,Chris

    Dry,No sealer needed,Chris
  11. Replies
    5
    Views
    404

    Well,Still very much in the biz...But due to...

    Well,Still very much in the biz...But due to several issues I don't have full control over we have been delayed way more than expected.Things are improving,and we are catching up,not as fast as I...
  12. So,lets revisit the rotated sleeve,and decide why...

    So,lets revisit the rotated sleeve,and decide why in fact it rotated.Two strongest possibilities...
    1,Insufficient interference from the factory allowing rotation when the motor got a little hotter...
  13. The sleeve turned for one of two reasons,either...

    The sleeve turned for one of two reasons,either there was not adequate interference between the register(aluminum block holding the sleeve) and the sleeve,or an overheat occured that allowed the...
  14. Replies
    4
    Views
    392

    Our reeds are available as reed only sets or...

    Our reeds are available as reed only sets or combo reed and stuffer sets for most motors.As to pricing,I can't control what a reseller does,but we do sell direct...See our website or call for...
  15. Replies
    4
    Views
    330

    Very common for the metal reeds in your motor to...

    Very common for the metal reeds in your motor to break,sometimes causing serious(rebuild time)damage...We have a composite that improves performance and is safe in case of breakage,call if you want...
  16. Replies
    6
    Views
    537

    way way lower

    way way lower
  17. Your BB block is actually a 150 HP,if I remember...

    Your BB block is actually a 150 HP,if I remember correctly...Pretty sure.A 175 would be a CC block.The ports are smaller in the BB,Chris
  18. Replies
    9
    Views
    430

    We have reeds and stuffers,gaskets for your...

    We have reeds and stuffers,gaskets for your motor...the metal reeds chip and break often,it's a good idea to change to composite.Also,check your fuel pressure at idle,should be 36=39 lbs,if the...
  19. Replies
    5
    Views
    356

    I can help with the gaskets and install,give a...

    I can help with the gaskets and install,give a call,Chris
  20. Replies
    5
    Views
    356

    Yes,I would advise to carefully lap the cages on...

    Yes,I would advise to carefully lap the cages on 400 wet/dry paper and a little soapy water.Be especially careful to hold the cage flat,and don't allow any rocking.A lot of lapping is not...
  21. Replies
    5
    Views
    356

    Not at all normal,Give a call and I'll see if I...

    Not at all normal,Give a call and I'll see if I can help,305-394-3354,Chris
  22. Replies
    13
    Views
    688

    Patent Help

    Anyone farmiliar with the patent process that might offer advice,I have an idea I think might be patentable,but am not sure where to go next.Once before I had something that cost several thousand in...
  23. Replies
    3
    Views
    236

    Your motor is equipped with 5 petal carbon...

    Your motor is equipped with 5 petal carbon reeds,so you should be good for awhile...when the time comes,we have a much more affordable alternative,Chris
  24. If you look around you can find good unhurt...

    If you look around you can find good unhurt cranks for less than the cost of a repaired one,I don't use repaired cranks,Chris
  25. Replies
    5
    Views
    489

    The block can be heated to remove the sleeve,or...

    The block can be heated to remove the sleeve,or the sleeve can be carefully split longwise,it will collapse enough to be removed by hand,as long as it isn't beat up at the ports,or bulged.Once the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4