Price for a Ghost 47 and 3in1 nosecone. Thank you!
Type: Posts; User: gray1402
Price for a Ghost 47 and 3in1 nosecone. Thank you!
I have a 2000 Ranger 518SVX Comanche with a dual axle trailer which was damaged Saturday in a wreck. It's just the trailer, (as far as I have been able to tell) pretty much destroyed the starboard...
So where can I buy / find the Y cable?
Serial #OG680518 1998 Mercury 200 EFI has began to randomly not crank or turn over. It will crank and run with no problems. I can stop and fish, move two or three times without issue, then go to...
PT, You can look at what is posted here too..http://www.bbcboards.net/mercury-2-0-2-4-2-5-liter-high-performance/536460-temp-gauge.html
Just so you see what was said in context....
Thanks Don...
I have noticed that when I hit the trim button on the side gear control, it makes the Tach move higher and/or then lower or a combination. The Tach is working fine but as soon as you start trimming...
When the motor was taken in for rebuild, it had less than 2 hrs on the impeller. I was told that it was going to be replaced but when I went to the lake to do some breakin, I didn't have the water...
So could injectors not being serviced cause a loss of compression or a blown cylinder? I am reluctant, to actually take and begin breaking the motor in because there have been a couple items I...
What would be some of the symptoms of this occuring? Also, could this have been the reason for a cylinder ultimately losing compression (going from 120 to 60)? This occurred while at WOT(thus causing...
well my situation is this, I don't know for sure if the injectors were serviced when the powerhead was rebuilt. I figure if I am going to have to have that done and this is a MUST HAVE or the...
OK, say I picked up this above motor, 1998 2.5 200EFI that just had a new powerhead installed. If I want to get "more power" out of that motor, what would you do next to the motor? Let's just say...
Don I really appreciate your input!
Be well,
G
CORRECTION:> I APPRECIATE EVERYONE'S INPUT:popcorn::thumb up2:
yep Tx, that is what I wondered most, if 250-275hp was obtainable without spending crazy money, however, I do want to run pump gas (although I don't care if it's premium gas) and I want the motor to...
let me hear from you high performance guys.
ok, been wondering this for a while. lets say you began with a blank canvas motor,1998 or later Mercury 2.5 200EFI. What is the most horsepower you can...
Slimm, that is VERY VERY slick. I relied and trusted the alarms when I bought this motor and can say I am now the proud owner of a new powerhead. When I had it installed, I asked them to remove the...
I have a 1998 Mercury 200EFI 2.5 liter motor SN#OG680518 and on my new powerhead I have decided to install a temp gauge instead of relying on the alarm alone. Which teleflex gauge would I use and is...
Thanks, the info, what I have and what you referred me to are the same...:thumb up2:
On the oil injection, let me just say, make sure your lines are factory and not something put there because...
I know it's here somewhere, just can't seem to find it lol... OK, just got a new power head on my boat. The motor is a 1999 Mercury 200 EFI (2.5), oil injection was removed (which was what caused me...
I may have to have my 1998 Mercury 200 EFI (2.5L) power head rebuilt. I have been told that I can get a decent amount horsepower while rebuilding it with some tweeking. I was just wondering, would...
Yeah, I kind of thought that. But, just to make sure, I thought I would ask on here because this is the most comprehensive website with people :bows: that have a wealth of knowledge that REALLY know...
I started talking to someone the other day at the boat ramp and we got on the subject of Seafoam and Sta-Bil which we both use each time we fill our tanks. He went on to tell me he also added Seafoam...
Don
I appreciate it. I have someone that is going to look into it and see what is the best option for repair. I agree, I didn't think the 3.0 would fit but it was worth a shot. I may be able to...
Well I finally did something that everybody is gonna do at some point. I hit something in my boat with my motor, 1998 Mercury 200 EFI, and damaged my prop. After I took my prop off I noticed that I...
Well Cheatham, I am keeping my fingers crossed http://www.bassboatcentral.com/smileys/praying.gif ...I just put a high speed low drag 10 inch Hydro Dynamics Jack plate on my Fisher ...
Well for future reference, Island Cove Marina on HWY 58 has some options. They have both Waterfront Cabins which are REALLY nice and a Hotel. If you have some others that are fishing the same...