Search:

I just got my new Quest, and other than it and my mega 360, I am a Lowrance guy. On my previous Ultrex I was running a AI 3 -1 Transducer below the TM motor. I would like to put this transducer back...

I just got my new Quest, and other than it and my mega 360, I am a Lowrance guy. On my previous Ultrex I was running a AI 3 -1 Transducer below the TM motor. I would like to put this transducer back...

I got on the phone with the folks at Bass Cat and they were super helpful and have my grade 8 bolts on the way to me. I was wanting to see if anyone on here knew what the torque lbs spec was for...

Hey Guys! Jumped on here to get some advice and found this thread. I have a 2017 Z520C boat with the 17" wheels. Ever since I bought the boat (2018) I have had a problem with the tires towing out at...

Thank you for the advise! Turns out it was the solid state start panel was bad. Moisture got into it and caused a hard short, preventing the engine from cranking. Ordered new panels and should get...

I need some good advise folks! This past Saturday I put my boat in the water, I entered my code to crank and hit the start button and nothing happened. No beep either. The only thing that was...

Thank You to everyone whom has responded to this post! I really do appreciate it and may take some of you up on your offer and contact you to discuss further! Thanks again!

Thank You very much for the assistance! I know I do not have a fluid leak, so you may be spot on with the short. Like you said, very frustrating and I will be heading to Seminole in mid February from...

I have a 2017 Z520C and are having the same problem with wearing out tires on the inside. I have taken the wheels off and torqued the spindle bolts, but the problem persists. I do not think it is a...

Need some advice before having to take trailer to Ranger dealer. For no particular reason my lights and brakes have quite working on my trailer. When I hook up to my other trailers, lights and brakes...

A freind of mine recently shared some waypoints with me for a particular lake and yesterday I tried to enter them into my Live 12" and for some reason, it would not take the higher numbers within the...

Thank You guys so much!

I am sure this question has been asked before, but I need to ask again. I have taken a 24V Motorguide off of a 19' Aluminum Triton Bass boat and have replaced it with a 24V Minnkota Fortrex. The...

I have been running the CMAP Precision HD (South Carolina) for a year or two now and love it! I really need a chip for GA lakes and when I go to CMAP website it is very confusing as to which one I...

When I go to SS page, it shows source as "this unit" but still black for down and side. It allows me to change frequencies, but it makes no difference. My box is in the console, so I will need to...

I recently went through the effort on my 2017 Ranger 520c and ran a completely new dedicated electrical system for all my electronics. I ran 8 gage wire to blue seas fuse panels at console and bow...

Thank You so much Guys for all the advice and info! Greatly appreciated!

When measuring Prop to Pad, due I measure to the far length of the prop or where the prop starts?

Sorry! I failed to mention which model it was. It is a 189 TRX

My oldest son just recently bought his first boat all by himself and is having some issues getting the boat up to full speed. It is a 2016 Triton TRX with a 150 hp Evinrude, w/o a jack plate and he...

TC, you said save waypoints but not settings, how come? I always save both so I can re-install after hard reset. Just curious why not the settings also?

Thanks guys so much!

Does anyone know if the Humminbird M360 will work on the Ghost TM? I apologize if this question has already been asked here! Thanks!!!

I am sure someone has already asked this, but can you put the M360 on a Lowrance Ghost TM?

Thank You very much!