Search:

Type: Posts; User: hooken203

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    1
    Views
    170

    XB21 300R BRV5

    Is anybody running a PowerTech BRV5 on their XB21 300R set up?
  2. Replies
    0
    Views
    71

    32 pitch Bravo FS

    For sale 32 pitch Bravo FS. As stock as it came out of the box no repairs or mods have made to it.
    700 dollars TYD. Message me if you have any questions.
  3. Thread: 28 Brave FS

    by hooken203
    Replies
    1
    Views
    169

    28 Brave FS

    28 Bravo FS in excellent condition. It has never been worked or repaired. 4 PVS holes were added to improve the holeshot. 700 dollars TYD. Please message me any questions.
  4. Replies
    21
    Views
    682

    This is a great discussion. I think that if you...

    This is a great discussion. I think that if you run Dons recommend cocktail all the time you will have to worry less about what fuel you run. I have ran 91 and higher octane in all of my outboards...
  5. Replies
    11
    Views
    1,001

    Bravo XS and FS are the same length barrel. XS...

    Bravo XS and FS are the same length barrel. XS has 8 holes and FS has 4. Some early Bravo 1 had no holes long barrel with a flare then they came with 4 1 inch holes you couldn’t plug.
  6. Replies
    0
    Views
    195

    Shimano Antares DC 7

    PRICE REDUCED!!
    This is a left hand reel. Antares DC 7. It is in very good shape and works as it should. It comes with everything as it had new. Box, reel cover, oil and paper work. $225TYD PayPal...
  7. Replies
    8
    Views
    293

    Thanks for the response Joe. I have always used a...

    Thanks for the response Joe. I have always used a remote start switch to jump the solenoid if it’s easy to get at. I like to know what that first compression jump is. But every time I learn one of...
  8. Replies
    8
    Views
    293

    So if you don’t use the key switch but instead...

    So if you don’t use the key switch but instead jump the solenoid then you don’t have the compression loss through the air injector’s. Is that correct?
  9. Replies
    8
    Views
    293

    Ok thanks. That’s what I thought. I was told...

    Ok thanks. That’s what I thought. I was told different by a Facebook expert.
  10. Replies
    8
    Views
    293

    Compression question

    SER# 1E 053049
    300XS
    When checking compression how will the air injectors affect your readings? Should they be disconnected when you check it?
  11. Replies
    15
    Views
    1,218

    I switched to a 300 R March of 2020. It’s a very...

    I switched to a 300 R March of 2020. It’s a very impressive engine. I finally have a boat that will run mid 90s.
  12. Replies
    15
    Views
    1,218

    Good to see you post up here again Steve.

    Good to see you post up here again Steve.
  13. Replies
    5
    Views
    329

    Looked excessive to me. I didn’t put nearly that...

    Looked excessive to me. I didn’t put nearly that much on it going back together. Thank you for the info Don.
  14. Replies
    5
    Views
    329

    That’s what I thought Joe. From what I know the...

    That’s what I thought Joe. From what I know the stuff isn’t cheap so why would you slather it on like bbq sauce.
    Thanks Joe.
  15. Replies
    12
    Views
    994

    I am not going to install one. To many reasons on...

    I am not going to install one. To many reasons on the negative side to go ahead with it.
  16. Replies
    5
    Views
    329

    Heat sink compound?

    97 Mariner 150 0G508602
    Is it really necessary to use this much heat sink compound?
  17. Replies
    12
    Views
    994

    Yeah that’s where I started. That weak metal in...

    Yeah that’s where I started. That weak metal in the skeg is the same weak metal in the hollow cavitation plate. I learned from one of Tim’s testers that it really didn’t make much difference. Also...
  18. Replies
    30
    Views
    1,655

    I remove my prop a lot and notice it is not at...

    I remove my prop a lot and notice it is not at the proper torque every time I remove it. I thought the nyloc nut and/or Belleville washer were worn out. Replaced the prop nut and washers next time...
  19. Replies
    12
    Views
    994

    Foil on a Pro XS or an R engine.

    Has anyone seen a hydro foil on these engines? I have one sitting here. Thinking about trying it to see if it will help my hole shot problem. Just wondering if the casting is weak and that’s why you...
  20. Replies
    21
    Views
    1,478

    I found it was like a cult. If you bad mouthed...

    I found it was like a cult. If you bad mouthed Hydromotive or Allison boat you got banned. Found that out right away. No room for discussion there.
  21. Replies
    8
    Views
    411

    Still waiting for parts on this problem. Come on...

    Still waiting for parts on this problem. Come on Mercury you can do better.
  22. Replies
    6
    Views
    373

    Yes mine are doing the same as yours. Aren’t they...

    Yes mine are doing the same as yours. Aren’t they tubes just like what’s in a golf bag?
  23. Replies
    7
    Views
    493

    Will transducer 000-14886-001 read 200khz 83khz...

    Will transducer 000-14886-001 read 200khz 83khz medium and high CHIRP?
  24. Replies
    7
    Views
    493

    I installed this transducer today. What should I...

    I installed this transducer today. What should I set for transducer type? I don’t see the letters on the tag listed on my unit. It only works on medium CHIRP.
  25. Replies
    7
    Views
    493

    Thank you that describes at the problems I am...

    Thank you that describes at the problems I am currently having.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4