Search:

Type: Posts; User: Lrrsme

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    17
    Views
    633

    If you decide to get a guide check out McCotters,...

    If you decide to get a guide check out McCotters, one of the best on the lake.
  2. My niece suffered from migraines most of her...

    My niece suffered from migraines most of her life, started in her teens. Hade a ton of tests and diagnosis, turned out to be lupus. Took about 12 years to get it figured out.
  3. Thread: Bed Cover?

    by Lrrsme
    Replies
    38
    Views
    985

    I have a BakFlip, sturdy, you can stand on it....

    I have a BakFlip, sturdy, you can stand on it. Leaks a little though.
  4. Replies
    74
    Views
    7,419

    508985

    508985
  5. Replies
    2
    Views
    194

    I think the bottom cousin just pulls out of the...

    I think the bottom cousin just pulls out of the base, it is a tight fit.
  6. Who did you order the kit from?

    Who did you order the kit from?
  7. Thread: Wiring Mystery

    by Lrrsme
    Replies
    8
    Views
    531

    The AC part does but the DC part uses the ground...

    The AC part does but the DC part uses the ground cable and charges the 3 trolling motor batteries in series.
  8. Thread: Wiring Mystery

    by Lrrsme
    Replies
    8
    Views
    531

    Stealth chargers use a wire from a trolling...

    Stealth chargers use a wire from a trolling battery neg. to start battery neg.
  9. Thread: 2014 pathfinder

    by Lrrsme
    Replies
    14
    Views
    529

    You need an alternator. Low voltage shut the...

    You need an alternator. Low voltage shut the controller down, failsafe.
  10. Replies
    4
    Views
    272

    I got a set from C&O marine.

    I got a set from C&O marine.
  11. Replies
    24
    Views
    1,826

    Is the other part of the thrust washer stuck in...

    Is the other part of the thrust washer stuck in the prop?
  12. Replies
    23
    Views
    1,225

    After the flash I was able to run more prop,...

    After the flash I was able to run more prop, better hole shot and picked up 6 mph. Usually don't run it very long at higher rpm, try to keep it around 62-6300. Still pulls hard.
  13. Replies
    23
    Views
    1,225

    Mine would run 6100 with no problems now after...

    Mine would run 6100 with no problems now after the flash it's turning 6600
  14. Thread: DigiQ.

    by Lrrsme
    Replies
    11
    Views
    640

    Not for me either, used mine twice also and...

    Not for me either, used mine twice also and that's it.
  15. Replies
    4
    Views
    237

    serial number and there's a number on the bottom...

    serial number and there's a number on the bottom of the pedal that you will need.
  16. Replies
    108
    Views
    11,448

    469334

    469334
  17. Replies
    11
    Views
    770

    I was looking for some Motorguide parts and...

    I was looking for some Motorguide parts and couldn't find anything local, ended up calling C&O marine in Tennessee where I bought my boat, they were very helpful and I had my parts in a couple days.
  18. Thread: 2014 250 SHO

    by Lrrsme
    Replies
    6
    Views
    385

    My boat has a 2015 250 SHO on it and almost...

    My boat has a 2015 250 SHO on it and almost didn't buy it because of that, have only owned Mercury's before this and don't have a good shop close by. I have no regrets now and I love the motor, would...
  19. Replies
    10
    Views
    503

    I work on them, there pretty good besides the 2...

    I work on them, there pretty good besides the 2 issues mentioned we see some cat. converter failures and some cam sensor issues.
  20. Replies
    11
    Views
    617

    All the Bob's plates I have owned had a gauge.

    All the Bob's plates I have owned had a gauge.
  21. Replies
    18
    Views
    1,548

    Don't know about mixing the two but you can get...

    Don't know about mixing the two but you can get stuff to thicken gel into a paste, just google it.
  22. No ramp at National Harbor. Pohick is not far...

    No ramp at National Harbor. Pohick is not far from Marshall Hall at all. My buddy is fishing it and said launch was out of Smallwood in Mattawoman.
  23. I use super glue, worked great.

    I use super glue, worked great.
  24. Replies
    7
    Views
    355

    Saw a add on facebook for a company that makes...

    Saw a add on facebook for a company that makes them, Google it, you will find something.
  25. Replies
    25
    Views
    1,471

    The metal plate should be screwed to the boat.

    The metal plate should be screwed to the boat.
Results 1 to 25 of 180
Page 1 of 8 1 2 3 4