Search:

Type: Posts; User: yupitsme

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Thread: What is this?

    by yupitsme
    Replies
    3
    Views
    595

    If you have smart craft gauges/wiring - It could...

    If you have smart craft gauges/wiring - It could be the wiring for the remote oil tank sensor. Your tank may not have the level sensor installed.
  2. Replies
    22
    Views
    878

    Take the batteries out. Transport them to the...

    Take the batteries out. Transport them to the house and charge them there. There is no real good option for charging the batteries sans a reliable electric source. Or... portable generator powering a...
  3. Replies
    7
    Views
    405

    check the hull for damage. May have to jack it up...

    check the hull for damage. May have to jack it up a bit to clear the bunks if initial inspection does not reveal anything.
  4. Replies
    30
    Views
    1,066

    able to run on high(or higher) setting without...

    able to run on high(or higher) setting without damaging the motor.
  5. Replies
    8
    Views
    482

    The conversation here is about an Outlaw hull. An...

    The conversation here is about an Outlaw hull. An Outlaw hull does not a 209 make. As we discussed in an earlier conversation - get your p-2-p right then start trying to dial in the 27p Trophy plugs....
  6. One, larger of the two, appears to be an HDI...

    One, larger of the two, appears to be an HDI transducer. Should work with any HDS head unit. Might work with elite series as well but someone else will have to sound off on that issue.


    The...
  7. Replies
    9
    Views
    419

    I'm puttin' my money on "The Debil did it!"

    I'm puttin' my money on "The Debil did it!"
  8. Replies
    9
    Views
    419

    Is the back lighting level the same on both...

    Is the back lighting level the same on both units? The amount of "draw" the unit has directly impacts the voltage reading of that unit. Also if you have more/different transducers this can impact the...
  9. Replies
    5
    Views
    294

    "IF" it's epoxy adhesive at heat gun, not a hair...

    "IF" it's epoxy adhesive at heat gun, not a hair dryer, will soften it up making it possible to remove with a sharp scraper. A heat lamp can have the same effect but takes a tad longer. Just use...
  10. Replies
    7
    Views
    286

    Navionics has a "Easy View" menu selection that...

    Navionics has a "Easy View" menu selection that significantly enlarges the waypoint icon/name.
  11. Replies
    9
    Views
    469

    :thumb up2:

    :thumb up2:
  12. Replies
    9
    Views
    469

    7/8" bore brush. Chuck it up in a drill motor. Be...

    7/8" bore brush. Chuck it up in a drill motor. Be sure to vacuum hole when done - $6

    528356
    ...
  13. Thread: Knowledge

    by yupitsme
    Replies
    17
    Views
    622

    On all but the rarest of occasions: "The teacher...

    On all but the rarest of occasions: "The teacher learns more than the student." Good teachers that is.
  14. Replies
    9
    Views
    795

    You are correct!

    You are correct!
  15. Replies
    9
    Views
    795

    Mmmm... no. When a warranty claim is honored and...

    Mmmm... no. When a warranty claim is honored and a new unit shipped the warranty clock does not reset. If you had, say, 8 months remaining on the original purchase - you'll have 8 months remaining on...
  16. Thread: Active target

    by yupitsme
    Replies
    7
    Views
    499

    Mmmmm.... How can the Elite "flash and shut...

    Mmmmm.... How can the Elite "flash and shut off..." when the Elite isn't even powered up - If you powered up the AT first and let it stabilize before powering up the Elite as recommended?

    If the...
  17. Thread: Active target

    by yupitsme
    Replies
    7
    Views
    499

    Run temp power cables for the Elite fs direct to...

    Run temp power cables for the Elite fs direct to battery. Then power up AT and see if issue is still present. Or.... if you have the ability to power the AT on first. Let the AT boot all the way up...
  18. Thread: Active target

    by yupitsme
    Replies
    7
    Views
    499

    Probably low voltage caused when the AT starts...

    Probably low voltage caused when the AT starts up. Could be battery but most likely wiring is the issue. Insufficient ga wiring to carry all that's on that particular circuit...
  19. Replies
    24
    Views
    1,240

    Mangled indeed! :laugh::beers:

    Mangled indeed! :laugh::beers:
  20. Replies
    24
    Views
    1,240

    https://images.contentstack.io/v3/assets/bltab8525...

    https://images.contentstack.io/v3/assets/bltab8525fe5f7bb21b/blta327779ea2171ea4/63bf67294933ee68391a0276/SMG11HD_ProductImage_PrimaryImage_1500.jpg?width=1280&quality=75&auto=webp
    FEATURES AND...
  21. Replies
    15
    Views
    1,177

    Your steering input is countering natural and...

    Your steering input is countering natural and unavoidable prop torque. It does not matter if you have cable or hydraulic steering the prop torque is there. When you cut the throttle prop torque goes...
  22. Do you have a Stealth 1 charging system? And...

    Do you have a Stealth 1 charging system? And actually... that ground wire is connected to, or should be, the #1 trolling battery wired in series. You can tell the #1 battery in a series - it's the...
  23. Replies
    10
    Views
    649

    Just as a test... Reconnect the old Point 1 and...

    Just as a test... Reconnect the old Point 1 and see if it works now. You might end up with a spare Point 1. You don't have to re-install it. Just see if it's visible on the NMEA network.
  24. Annnd... My instructor said "When the plane...

    Annnd... My instructor said "When the plane clears the ground you will experience prop torque to the left. Counter it with right rudder!" Sho'nuff... wheels cleared the runway. Prop torque to the...
  25. Replies
    4
    Views
    266

    I got cardboard boxes - big ones. Cut them up to...

    I got cardboard boxes - big ones. Cut them up to the shape LxWxH to fit the ProTour I was shipping to a buyer. You have to make the bottom and the top to go over it. Once you have the bottom made get...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4