Search:

I love my 36V Ultrex with 52 inch shaft I got from Tim.

I'm running a 250ProXS on my XRS and have added 2 inch blocks to the jackplate to get 16 inches of setback. The extra leverage will allow you to achieve bow lift with less trim. I'm running a Bravo...

I just had a 52 inch installed Tennessee style on my XRS. It replaced a 45 inch Fortrex. The other day in high wind without putting it down further in the water the prop broke out from time to time.

Actually in fixing mine Lawrenceburg Marine Used the V-1 Valve & Actuator and the cable off the T&H Marine setup. So a new cable wasn't necessary.

I also have the extended warranty and can't think of any reason why the foil should cause a problem. In fact if you shed a blade it will help protect your lower unit. It will also help with...

Last November I bought a 2016 XRS from Lawrenceburg Marine. Last week while fishing I used my Liveweel after draining it I attempted to close the remote drain and the actuator arm broke. I knew...

I've got a 2016 XRS with a CB Marine foil and 2 inch spacers. I have a 250 Proxs with verado lower unit and have run 80.2 with my 28 Bravo 3/4 inch below Pad. It lifts and runs well. I know that...

The internal transducer doesn't do down imaging, the external can. I like down imaging.

I have read that in the past you decided that 14 inches of setback on the motor is ideal on the 21X boats. I have a 21XRS which has a different balance point which is further forward and it also...

I will be there. It's only about 40 miles from home.

I went over there and told them many of the fellas they missed had defected to over here. LOL

I have a 21XD and I am running white boat bumpers inside my jackplate. The ears on each end stick out of the holes in the side of the jack plate. I have a skid plate on the bottom of the jack plate...

When launching my boat I back the trailer until the hull floats up off the trailer then pull back forward and launch the boat. When loading I back down and wet the bunks thoroughly then pull forward...

I don't want any part of a cat. The guy who owned my Bullet before me had one. The boat had white cat hair all over the carpet when I got it and the cat also used the carpet on the front deck as a...

No matter how hard I look at that truck, it's still a GMC. Seems like while you had a chance to make a change, you would have tried to better yourself.:crying:

Prayers sent!:praying:

When I was looking for a Bullet to buy I went on Craigslist and kept expanding my search area until I found what I wanted. I was willing to travel 250 miles to pick up a boat if I found the right...

If they want to turn their backs on us that is a two way thing. They have had rally after rally at Euchee. Maybe the folks of middle and west Tennessee and the Alabama folks need to divorce...

What happened to Pickwick? I was good with that. Euchee, no thanks. Maybe the Bullet owners out of the Pickwick area could have their own.

I'm a little amused. Some people advise don't take along tackle you won't need that day but then add ballast to balance the boat. If you need the extra weight why not have it be tackle...

You still haven't told which Bullet model you have. You haven't told us whether your lower unit is a sporty or Tm. You haven't told us what gear ratio it is. And you haven't told us the pitch of...

That's a really nice looking boat. Now you simply have to go to a Ford dealer and get a good tow rig. A King Ranch Diesel would do nicely.

Ya'll are gettin personal and you might hurt his feelings. Shortcomings aren't supposed to discussed in an open forum.

I expect your engine has 8 holes on each side to bring in water in addition to those on the nose of the gearcase. I am running my 250SX 3/4 in. below pad. I had Lawrenceburg Marine plug the top 4...

I had a local shop which makes custom stainless salad bars and other items for the food industry, make me a bottom plate of my design from stainless steel. It is absolutely bullet proof. Was that a...