Ok thanks I’m at 3.75 below pad now that’s where my hull likes it best with the props I have, 10” plate with 2” spacers. I’m working away for a good while, I’m thinking when I get back I’ll try and...
Type: Posts; User: Red x21
Ok thanks I’m at 3.75 below pad now that’s where my hull likes it best with the props I have, 10” plate with 2” spacers. I’m working away for a good while, I’m thinking when I get back I’ll try and...
Thanks Mr. CJ, I’m not chasing speed anymore either, this 2002 x21 is hard to get the bow up and it’s hard to get the stern out the water to loosen up, it’s weight sensitive. I run a tic over 70 with...
6000 it’s a Yamaha vmax 225 ox66 sorry
Thanks Mr. Mike, what pitch would you recommend if turning a 25 tempest plus to 5900 rpm’s?
I know most say power tech props are junk on our boats. I run a tempest plus and trophy a45 with good results, but was wanting a prop that would carry heavy loads better. I originally wanted a bravo...
Sorry by not buy
Not fighting but want to put this out there referring to post on page 2.
cant smell def? That’s false my 2019 6.7 when it reigns at idle it smells pretty bad, and I had people ask me to turn it off...
Thanks for all your replies, all neat experiences I plan to return to the spot as soon as possible just got out the hospital from a kidney stone, I’m hoping it passes rather quickly, it’s not my...
Hope all is well, I made a deal with myself
if I ever caught a bass 7+ lbs I would have a replica made, well today was my chance I have caught several a little over 5 but today I hook one bigger...
Same block but I believe porting is a little different, atleast for a 200 and a 225 was. I was 5-6 mph slower when obr sent me a reman powerhead we pulled the heads and the ports were different...
Sorry should’ve made my self more clear it’s not moisture it’s from the sun. Thanks for the reply though.
Cracked welds at transom top and bottom, inside where braces tie into the transom, my 02 has a weld that runs down the center of the hull i’d Check it and other welds underneath on transom, welds on...
I hope all is well, I’m asking anyone who may have experience with this problem. I have Yamaha digital gauges that have hazed over and wondering the best way to clear them up again? I thought about...
Lol I put mine in gear also but my cable isn’t broke yet, the handle just doesn’t want to stay up. Follow the videos and instructions on cam install it isn’t bad at all, just tighten and loosen...
I really like my hot rod cams it’s like a whole different car, pulls better all the way to the top, did install myself which was way easier then I thought. Along with the other mods I’m catless with...
Thanks for all the reply’s I was recommended a centerforce clutch by a mechanic I know “talked to him after I posted”.
Mounts seem fine from what I can tell no excessive movement, everything feels solid.
150,xxx miles
2010 mustang gt has Hotrod cams, jlt series3 intake, Barton short throw shifter, and Brenspeed tuning. My issue is under acceleration I can feel the clutch pedal move towards the floor as if it...
I have an 02 Xpress with a Yamaha vmax 225 ox66 full fuel and loaded with all my tackle, which isn’t as much as some but I consider decent amount, with 12” plate 3.5” below pad and a trophy a45 26...
Also if you have the Mayfair twist and lock cartridge pumps make sure the o-rings are good, mine had a bad o-ring and took on water.
Thanks for the replies guys, I’ll definitely check those products out.
I’m thinking of fully restoring my x21 dual console my questions are, what is the best primer, paint and clear coat to use on aluminum? I plan to re-primer and repaint to another color. And also...
Thanks fellas, I had the green and yellow Mr.Twister it just went out and has been lightly used. When you put pressure the blades would pretty much quit their motion they were suppose to be doing to...
Looking for options that people had experience with thks.