Search:

Type: Posts; User: geno368

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Trying to add Mega 360 to my Skeeter running an Ulterra

    I am running a G3n helix 9 on the bow. It is networked with a Helix 9 KVD g2. I need to know what I need to enable this Mega360 on the bow.
    Thanks
  2. Skeeter 1996 ZX180 floor dimension question

    I am handicapped with severe balance issues so I am trying to figure out a way to install a floor plate that is threaded for a 1/2 " galvanized pipe about 20" high that I can mount some type of grab...
  3. Replies
    31
    Views
    1,515

    Need new inflatable life jacket

    I have an old inflatable life jacket that is impossible to put on over a jacket or rainsuit. Is there a good one that is easier to wear??
  4. Thanks for the replies...I will follow through on...

    Thanks for the replies...I will follow through on the suggestion
  5. ser # 1B963709 859318t1 P175P73EY Thanks for...

    ser # 1B963709 859318t1
    P175P73EY

    Thanks for relies....I have not been pumping the bulb...I didn't think it was necessary if I hear the fuel pump load...please advise
  6. 175 Pro XS -Intermittent hard srart after long idle

    I have a 2013 175 Pro XS that has a weird issue. If I idle in gear for about 30 minutes while searching for structure the motor just quits. Sometime I have to wait 30-45 min before I turn it over...
  7. I found the problem...there were 2 wires in the...

    I found the problem...there were 2 wires in the control head that were touching each other and shorting..the insulation had slipped off....works fine now..
    Thanks for the help...Tight lines to you...
  8. Thanks for the replies....I will test further......

    Thanks for the replies....I will test further...
    I set my account up with immediate email notices when someone posts a reply but I never get any notices....I wonder why???
  9. Ulterra not working, guessing water in foot from seal leak..How to fix

    I have a 2016 Ulterra which has been great. All of a sudden, it just stopped turning the prop on 2 hot batteries. The remote shows the prop is turning...I talked to MinnKota and they suggested I...
  10. Replies
    2
    Views
    446

    Please disregard the question...my young son was...

    Please disregard the question...my young son was able to crawl in the back and found it...now I need to find the problem....the connection seems good.....any suggestions?
  11. Replies
    2
    Views
    446

    SKEETER ZX180 gas tank sender question

    I have a 1996 ZX180 with a 33 gal gas tank and the gas gauge is pegged negative position. I grounded the gauge and it pegged to full so I think my sender is bad or a wire is broken. I have looked...
  12. found one....

    found one....
  13. WTB Transducer XNT9-SI 180T for 798ci si combo unit

    Transom mount
  14. Thanks for the replies...I don't have a amp...

    Thanks for the replies...I don't have a amp clamp, so I am waiting for scheduling at our boat dealership...
  15. As I stated above, my battery and cables to the...

    As I stated above, my battery and cables to the motor were replaced by a retired marine mechanic and I checked over his work and all seems good. Engine cables are first...can I check amp draw at the...
  16. Would it be a possibility that the trim motor is...

    Would it be a possibility that the trim motor is going bad?..I acts normal when I am trailering and trimming up or down.
  17. When I am idling and try to trim up or down, the...

    When I am idling and try to trim up or down, the engine looses about half of it RPM's and when I am running it really cuts the power about half...I was running about 3800 rpm yesterday and trimmed...
  18. Thanks again for the replies...I have now...

    Thanks again for the replies...I have now replaced my battery with a 950 CCA marine battery and also replaced both battery cables from the battery to the motor. My cranking problem seems now gone. ...
  19. That's the info I needed...I will update my...

    That's the info I needed...I will update my battery...Thanks Silver Fox
  20. Thanks for the reply....I will check the link as...

    Thanks for the reply....I will check the link as well as replace the battery....any suggestions on a reasonably priced battery for my application?
  21. I have replaced both of the cable terminals with...

    I have replaced both of the cable terminals with top post direct connectors eliminating wing nuts. I did a load test on the battery and it showed good although it is a new Walmart 600 cca...The...
  22. Thanks for the reply...yes, I was thinking about...

    Thanks for the reply...yes, I was thinking about my old efi I used to have...it is a 2012
  23. 2003 Mercury Pro XS Engine nearly goes dead when running and accessing trim

    I am having some electrical problems I am working on. When I am idling and try to trim up or down, the engine looses about half of it RPM's and when I am running it really cuts the power about...
  24. Replies
    60
    Views
    2,016

    Fishing line snips needed that will cut braid

    I need to buy a pair of small snips that are good enough to cut braid. I have several that just frays the line....anyone know of such a product?
    Thanks in advance
  25. Thanks

    Thanks
Results 1 to 25 of 56
Page 1 of 3 1 2 3