Search:

Go to a Pool Supply store and get the O-Ring Grease for on the Filter O-Ring. I lube mine every 5-6 Months. Stays on !!

A 220 outlet should be a different configuration. I'd check the outlet with a volt meter to see tho. Let the chargers rest for an hour of two, then try them in a different outlet that you know is...

Is it in the stowed position or the deployed position ? Mounted or just on the ground ? You may have to push DOWN on the mount and then pull on the cord.

Unfortunately this is what I'm finding out !! I thought they were a reliable company !

Try using 2 3/8's oz A-Rigs hooked together end to end for a bigger profile and added weight to take it down deeper and keep it there.

I've fished Shasta many times and use a Tex-posed 6" Roboworm Morning Dawn on a #2.0 EWG with 12# Fluro leader. You just have to Finess it thru the trees, but need the 12# to drag them out !! Love...

I use a Shin knot for Braid to Fluro Leader and cut it to be twice the rod length. Then re-tie when the Knot is just outside of the tip.

Level the trailer unhooked, then measure from ground to the top of the hitch. Whatever that measurement is, that's what you want the top of the ball on the tow vehicle to be. Depending on your...

C & E Boat Restorations, England, Arkansas 870 575-3948 Curtis Massey He does AMAZING work !! I live in Fresno, Ca and when I get to where I need new carpet, I'm gonna drag it from Ca to...

My trailer is 2014 duel axle with Vault hubs and has never leaked or squeaked !! I carry a grease gun and a dead blow hammer. Should I have an issue, I'll pop off the cap, fill the hub with grease...

Place a light coat of RV-BLACK Silicone on the outside of the cap before you install it with or without an "O" ring. It will form an excess at the front of the cap as it goes in, do not wipe it off....

You should start by leveling the trailer tongue off of the vehicle. Then measure from the ground to the top if the hitch. What ever that measurement is is the height you want the ball on the tow...

Try hooking it directly to a battery, not a buss bar. It sounds like there are too many things hooked up to the buss bar. If it still flashes then contact Garmin.

I made an order a month ago and received a conformation and a note that there were some delays in shipping and they would let me know when it ships. Well, today I tried to send them an email to the...

Did you mount it on the motor or on the shaft ? If on the shaft, is it facing front to back and not side to side ?

Was the old plug a flat plug or a round plug, and how many pins ?

I've heard you can replace the whole relay setup with a $20 Wench relay from Am....... !

Bradrodfish where are you ???

Sounds like a bad or weak breaker. I'd start first with checking all the connections. Make sure they are all clean and tight. Then replace the breaker if it still does it.

I have 2 UHD 93sv units at the bow. One is for Live Scope and the other is for Chirp/Down/Side scan. Is there a Y-Cable that will allow me to use both units off of one GT56 transducer ??

I found this on Am....... over the trolling motor peddle, high rise and two graphs. Strong and stable in all weather. If I'm gonna make a long run, I can remove the Garmins from the cradles and...

I had a similar issue only mine was wearing on the inside of the tire. I pulled the wheel and noted that the splined end holding the hub to the torsion arm was not "Flat" in the arm mount. I...

It has to be deployed to work !

I've always used a "Snake" of Plumbers Putty and make it just a little larger than the transducer. Holds the epoxy and is easy to remove after use,

Not sure, that's just what my mechanic called it. I'd have it checked before just changing it, it was like $400, so You do need to have it troubleshooted by a qualified service tech.