Search:

Type: Posts; User: crappiehuntr

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    1,292

    Suzuki codes and low voltage white wire

    The title is for attention somewhat. I have experienced multiple codes stops run good then not start get home start fine then go several trips with no hiccups then same problem. I done all the usual...
  2. I fabricated a pole next to passenger's seat up...

    I fabricated a pole next to passenger's seat up to rail and 5' above the deck shoots great footage.
  3. Replies
    0
    Views
    267

    Front deck width

    Hey guys I need a little help I'm looking to up grade my bass boat. Looking for 18.5 to 20.5 foot boat my main attribute im in seach of is deck width at the seat post position my buddy has a z7 and...
  4. Replies
    51
    Views
    2,297

    mix me with concrete sink me with a hedge brush...

    mix me with concrete sink me with a hedge brush pile!
  5. Replies
    4
    Views
    158

    My 89 had a non floating float. If the jumping of...

    My 89 had a non floating float. If the jumping of the wires
    shows the guage to be working lift the arm after you remove
    the sending unit and see if the gauge works again if so
    you can replace the...
  6. Replies
    6
    Views
    715

    ANY BPS PROSTAFF MEMBERS ON HERE

    Im looking for a bps prostaff member to pm me I have a question.
  7. Replies
    15
    Views
    519

    I edited post and added pics

    I edited post and added pics
  8. Replies
    15
    Views
    519

    http://www.bbcboards.net/attachment.php?attachment...

    http://www.bbcboards.net/attachment.php?attachmentid=229963&stc=1http://www.bbcboards.net/attachment.php?attachmentid=229962&stc=1http://www.bbcboards.net/attachment.php?attachmentid=229964&stc=1http:...
  9. Replies
    15
    Views
    519

    Thank you and you are right about Reagan

    Thank you and you are right about Reagan
  10. Replies
    15
    Views
    519

    back to champion

    I recently purchased a really nice looking 89 184 scr with a 175 merc in Illinois. looks good and ran real good on my 5 min trip up the river it was said to be low hour and I think they were telling...
  11. Replies
    6
    Views
    503

    Thanks for the info I used the rubbers but if...

    Thanks for the info I used the rubbers but if they loosen on me I will change them. Thought maybe it could be done but looks challenging.
  12. Replies
    6
    Views
    500

    Ok thanks

    Ok thanks
  13. Replies
    6
    Views
    500

    Oil injection removal

    I have an 89 175 merc that still has oil injection hooked up. I see they make kits for removal but local boat shop says he just takes the drive gear out and puts pump back on any thoughts on this
  14. Replies
    6
    Views
    503

    Champion trolling motor install

    Is there anyway to gain access to trolling motor bolts on a 1989 184 champion or do you have to use the nuts that are in rubber thanks
  15. Replies
    7
    Views
    804

    I have not used imperial but I may try it. There...

    I have not used imperial but I may try it. There are a few spots that need reworked. I removed gas fill cap and hose and plan on lifting rear deck to fill tank, if I dont like that I will have to...
  16. Replies
    4
    Views
    598

    Check them with key on and off maybe leave one...

    Check them with key on and off maybe leave one hot wire and go to a new fuse block so you have an extra couple hookups if you need them.
  17. Replies
    7
    Views
    804

    Thanks for the acolades it has turned out pretty...

    Thanks for the acolades it has turned out pretty good, believe it or not but the one of the hardest things to do is getting the black to buff out right. The white and green was easy, I still dont...
  18. Replies
    7
    Views
    804

    I started this project in May of 2012 I had a bad...

    I started this project in May of 2012 I had a bad floor and decided to lift cap replace floor and check an area in the hull that had been repaired by myself after a trip to Truman reservoir in which...
  19. Replies
    7
    Views
    804

    bullet 19v into a 19xd

    Let me start by saying im no expert with gelcoat but i have done alot of boat work. That being said unless you really have a desire to bring a boat back to life reconsider a restoration, guys have...
  20. Replies
    1
    Views
    317

    Coming soon........

    Resto Bullet
  21. 2.3 minimum on the tip also to get mine to spray...

    2.3 minimum on the tip also to get mine to spray out flat I was at 55-60 psi on a vapor gun 2.3
  22. Replies
    6
    Views
    1,125

    I have it dismantled at this time but its 89 200...

    I have it dismantled at this time but its 89 200 merc and i wish I could help you with numbers but I cant remember where I ended up after moving it up and down I also have a 10" jack plate on it. I...
  23. Replies
    10
    Views
    740

    Thanks for all the encouragement and tips will be...

    Thanks for all the encouragement and tips will be ordering today.
  24. Replies
    10
    Views
    740

    New problem, US COMPOSITE tech guy says gel...

    New problem, US COMPOSITE tech guy says gel coating tri colors will be very hard to make look right because of thickness of gel goat. also removing tape could chip it. Anybody out there done a stripe...
  25. Replies
    5
    Views
    878

    thanks for the tips, I had thought of that and...

    thanks for the tips, I had thought of that and was planning to clean and repair some spots around the stringer as I go to help with keeping things in line. luckily only one side and less than half a...
Results 1 to 25 of 33
Page 1 of 2 1 2