Search:

Type: Posts; User: Savage

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    14
    Views
    118

    ^^^^This.....simple^^^^

    ^^^^This.....simple^^^^
  2. Replies
    13
    Views
    177

    On a racing hub I use EVERYTHING in the Mercury...

    On a racing hub I use EVERYTHING in the Mercury hub kit except the nut.
  3. Missed the no gears part......You likely lost the...

    Missed the no gears part......You likely lost the lower unit.
  4. Replies
    13
    Views
    177

    Same here. I NEVER had a problem with a properly...

    Same here. I NEVER had a problem with a properly torqued prop fastener coming loose, on any motor that I have owned.
  5. Replies
    3
    Views
    279

    My guess is piston ring pieces.

    My guess is piston ring pieces.
  6. Since the RPM data is accurate, that means one or...

    Since the RPM data is accurate, that means one or more of these things:

    The jackplate was set too high.
    The motor was over trimmed.
    The prop is damaged.
    The prop hub is bad.
  7. Replies
    13
    Views
    177

    Tighten with a Torque Wrench this time 55 lb/ft.

    Tighten with a Torque Wrench this time 55 lb/ft.
  8. Replies
    3
    Views
    170

    Drain BOTH oil tanks and run the DFI.

    Drain BOTH oil tanks and run the DFI.
  9. Are the RPM readings coming from a Smartcraft...

    Are the RPM readings coming from a Smartcraft Device?
  10. Replies
    14
    Views
    305

    Below is the torque specification on a Gen2...

    Below is the torque specification on a Gen2 Torquemaster.

    Fill Screw is 17 lb/ft
    Vent Screw is 60 lb/in.
  11. Replies
    2
    Views
    83

    Check cannon plug connections. Check the Main...

    Check cannon plug connections.
    Check the Main Power Relay.
  12. Replies
    3
    Views
    205

    The hull handles the same above 80 MPH, as far as...

    The hull handles the same above 80 MPH, as far as chine walk is concerned. The boat will always try to chinewalk.
  13. Replies
    13
    Views
    177

    Racing hub nut torque spec is 55 lb/ft. The...

    Racing hub nut torque spec is 55 lb/ft. The nylon in a nylock nut is not meant to maintain the torque spec, it is there so the nut doesn't fall off completely.
  14. Replies
    4
    Views
    94

    Read the sticky on throttle adjustment.

    Read the sticky on throttle adjustment.
  15. Thread: Boat Key

    by Savage
    Replies
    4
    Views
    187

    Mercury Dealer.

    Mercury Dealer.
  16. Replies
    15
    Views
    389

    Remove the strainer and flush adapter plate with...

    Remove the strainer and flush adapter plate with water. Motor is off and lower cowling removed.

    Can also back flush with the flushing port (see owners manual).
  17. Replies
    4
    Views
    94

    Your right the TPS linkage is not adjustable, so...

    Your right the TPS linkage is not adjustable, so the only thing you can do is adjust the throttle.
  18. Replies
    2
    Views
    99

    I would test the Tempest in the Summer.

    I would test the Tempest in the Summer.
  19. Replies
    14
    Views
    305

    Specs are in the Service Manual, if I get a...

    Specs are in the Service Manual, if I get a chance tonight I'll post them.
  20. Replies
    6
    Views
    130

    Your RPM'S are right where they should be, so you...

    Your RPM'S are right where they should be, so you are likely maxed out.
  21. Replies
    57
    Views
    1,520

    The passing of a dog is always tough for me to...

    The passing of a dog is always tough for me to take...….Sorry for your loss!
  22. Replies
    4
    Views
    94

    Get bleed hose from a Mercury Dealer.

    Get bleed hose from a Mercury Dealer.
  23. Thread: Prop for 18TRX

    by Savage
    Replies
    27
    Views
    316

    You cant "drive through" chine walk, you must...

    You cant "drive through" chine walk, you must control it with the steering wheel BEFORE it begins.
    PTP is measured with the pad of the boat and the prop shaft level to level ground.
    ...
  24. Replies
    14
    Views
    452

    Diaphragm appears to have a bad crimp on it. The...

    Diaphragm appears to have a bad crimp on it. The washer under the crimp looks cocked.
  25. Low water pick ups MUST be blocked. Are you...

    Low water pick ups MUST be blocked.
    Are you turning on the house water supply with enough flow?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4