Search:

Need recommendations for someone who can fix trailer fenders, rust etc. Along the bunk board carpet. I'm in Holly Springs area.... is Auto Marine in Garner still open?

Yes, slight turns to the left, just so you can feel the wheel tighten, then back off right....

I got the Bass Cat weather stripping and put in last year, bone dry, but it is bulkier so you have to punch the hatch down to turn the latch to close it, but very easy to install. Good quality.

What kind of rpms are you running at 69? Water pressure is fine, need more set up info...don't raise the engine much, better to learn to drive thru the chine walk.

I have an 08, same problem with 26 tempest and rev limiter. 27 turned great at top speed, but hole shot sucked. 26 Fury solved the problem. Hit 74.92 with the 27 tempest, hit 74.0 with Fury... With...

Found stress cracks on my transom shortly after I bought mine new. Spoke to the dealer, sent good pictures, and they took care of every last one. The guy at the glass shop basically handed me a...

Is the hull similar to the TR196?

That first pic at the top is the drivers seat. They are splitting at the seams. They would have to be reupholstered....

Love my 196! Got mine in 08, priced within the budget, and you can keep up with the big boys. Had a 186 before, big difference in storage and ride! I also like the fact that you need to learn how to...

Came from Triton back in 2008 had some warranty work done and the rep at the time said I will need new seats. Instead of putting them in right away, I stored them and got my $$$ worth on the old...

There's also a screw directly on top too, when removing the old ones I just ripped it out, putting the new ones in, had my son pull back the seat so I could drill and bolt them into the glass behind...

It was a job but I got them in... Emailed Triton, they were helpful. No good way to put new holes in the back of the new seats and into the glass... I wound up filling the old holes with silicone...

I'm guessing I should move over the vent so it's not squashed in back of the new seat.... Anyone? Also I will be putting up detailed pics because this is a pain! Yes 2 bolts in the middle of the...

Took out the 3 screws at the bottom by the floor. How do I get to the screws that are holding it on the back? Tried feeling around, couldn't find anything. It won't slide up. What's the trick?

I actually got the new seats under warranty, while some other "cosmetic" warranty work was being done when I first bought the boat... I told them to leave the old seats in, and have had the new ones...

$10 electrician fish tape/ snake... Best $10.00 spent!

Changed plugs, did compression test, still no luck. Brought it up to Angler's Choice in Va, they hooked it up to the computer. Needed a new coil on one of the cylinders. Stopped by the lake on the...

$600 to redo the old seats or just to install new ones???

My 2008 TR196 has the original " 1 piece seats" that everyone had to replace because they split at the seams. I've had the 2 piece seats stored for a while, and just getting all I can out of the...

I have a 2007 Optimax 200. Last week running up the lake I felt a little skip in the engine, rounded the corner and noticed I couldn't get back to wot.... I stopped, and went to hit the hot foot, I...

I run a 26 fury year round with a 200 Optimax and can hit 74+ in the winter....

Awesome boat, i love mine. You will have to learn how to drive it in different situations, to get the best performance. This boat likes some chop on the water, and it flies!

I agree, their service is next to none, had a few minor issues just a few months outside of the warranty and they took care of me.
saving up for a second one!

Go online, to the site, it has PDFs for all the manuals

I've been to the one in Portland Maine, I would very much prefer to shop at Cabellas... This BPS in Cary is lacking a lot...