I do have the factory manual.
I have pulled the exhaust plate and have ordered the gaskets I need to replace. I did make a mistake as the leak was from another plate that is sitting on top of...
Type: Posts; User: pamlicopanther
I do have the factory manual.
I have pulled the exhaust plate and have ordered the gaskets I need to replace. I did make a mistake as the leak was from another plate that is sitting on top of...
[QUOTE=leonreno;11513904]I believe the box can be done away with BUT you have to reset the timing afterwards and you have to hook up some wires the right way. I don’t know the exact procedure but...
I have not done the link and sync so that would be in order. I just noticed a water leak from the exhaust manifold behind the bracket that holds the coils. I need to pull that and figure out why...
I have a 1991 Mercury Black Max 150 that is driving me crazy.
Serial: 0d021340
Model: 1150412LD
This past spring it got where it was running bad and I began diagnosing my problem. I narrowed...
OK
Thank you all for your help.
In my research before this thread I kept running into issues such as the wiring gauge and all.
I plan to upgrade the trolling motor in the future and redo...
So if I do it this way I run the battery negative to the trolling motor negative and run one positive to trolling motor. Do I connect to the red or orange wire from trolling motor connector or do I...
OK - I have searched the forums and have gotten good information, but I am not sure I still have what I need to fix this thing.
I have a 1990 Astro Fish and Ski. I have a Motorguide Brute with a...
My 1991 Black Max I bought last spring is running good, but as part of my effort at ongoing maintenance I decided to change the fuel filter. I entered the serial number in a parts search and got...
I have looked over and over this engine and I cannot find any spot for adding a hose for a pressure gauge. IN my research it seems that some engines require you add a tee in between the hose from...
I will check it out.
What forum for more info?
Hello.
I have a 1991 Black Max (ODO21340) that I would like to install a pressure gauge on. I already have a gauge with the hose and fitting. Problem is I cannot find where the fitting screws...
Thanks for the picture help.
What the picture shows is the 2 sections of the ladder. I need something to fit in the holes and hold the sections together but still allow the bottom section to fold...
The one I keep getting told I cannot use because the file is too large to be added. I cant find a way to make it smaller so I cant add it.
Oh well I will try getting a larger rivet tool and get...
The connectors that hold the ladder together on my Astro Fish Ski came off. Here is a picture of what I am talking about. I am wondering what the best thing to reattach it. It looked to be some...
Actually, mine has just one large tank. Around 20 gallons seems to be close.
I meant to reply directly. Thanks - That sounds about right.
Thanks - That sounds about right.
Hello. I just purchased a 1991 Quickfire 18FS. I am getting her cleaned up and learning all I can bout her. I am trying to determine the gas tank capacity. I have looked all over and cannot find...
I am working on a 79 Wrangler right now. I had to pull the deck off the hull. I had to use a crow bar and other creative means to remove all the old wood from the transom area. I ended up having...
Thanks for the response.
This morning I went ahead and tried it and that was how I did it. I dropped the bow down first and very slowly let the back side go down. As I went along I made sure the...
OK - I have replaced the floor and transom on my 79 Skeeter. Everything is glassed in and now I need to drop the upper deck part back down on the hull.
What is the best procedure for me to follow...
Thanks - I was thinking that but wanted to make sure. This project has gone on way too long - I didn't want anything extra to do but didn't want to not do something too.
Thanks again.
Hello. I have finally gotten my new floor and transom in and I have gotten the new glass on it. My question is do you have to paint or put anything on these newly glassed areas? I know you would...
What kind of sealer would you recommend to use?
Hello.
I am about to replace my foam after installing new stringers. I am assuming you seal everything so no water can get back to the foam. My question is do you provide some means for...