I took my 04 H56 to brackish water regularly before I bought my bay boat. Just pop your cowling and spray everything down good with Corrosion X while you are spraying, get your battery connections...
Type: Posts; User: NotEarl
I took my 04 H56 to brackish water regularly before I bought my bay boat. Just pop your cowling and spray everything down good with Corrosion X while you are spraying, get your battery connections...
RL552, be sure to clean the little sniffer tube that is inside the mounting block for your O2 sensor before you run it. If that tube is clogged, the new sensor will not read properly.
Just got done doing the whole re-wire and install new electronics thing... come fishing at Lake Fork one weekend and I will meet you up there and help you get it knocked out...
I have a 193 dual console. A YETI 35 fits almost perfectly between the rod boxes and the consoles. Only a slight difference in height with the front deck. It makes for a small cockpit but extends...
I am right down the road from you. I have some powertech props that you are welcome to give a try. I have a 21 pitch and 22 pitch four blade. They are small diameter hubs but I have a spacer ring....
Shelled my lower last weekend. Fun-N-Sun in Hurst, TX had new and rebuilt HPDI lowers in stock.
Speed costs money..... How fast can you afford to go?
The bilge will stay dry. My batteries are not mounted in the center hole with the fuel tank like I have seen on a lot of Champs. My batteries are mounted in rear compartments that are on each side...
Update!!!!! Dropped my prop off at Steve's yesterday to have Josh double check the repair. He found something out of whack on the prop and got it straightened out. I have to hand it to Steve and...
I just got the prop back from Steve's have it repaired after a stump incident that destroyed my lower unit and bent the prop. I put a lower unit off of a 2005 VZ250 HPDI that has the low water...
I have a 1st generation Terrova 80lb. that I have been swapping out between my 193 and my 21ft bay boat. My spot lock works better in current than it does in wind. I have since put a Motorguide Xi5...
Have a 193 w/ 200 hp OX66 Yamaha on an 8 inch backplate. I don't have a prop to pad measurement because I run a hydraulic jack. I just got all of my gauges working so I know what she is dong now. ...
Why does ring free cost so much????? BECAUSE IT WORKS!!!!!!
Well from the pictures, both of your motors are 200hp. If they are similar model years, most likely they will use the same engine block. I would check and make sure both engines had the same...
I am by no means an expert, but on the later models, as long as the year model is similar and the engine block has the same displacement, I would think it would be a simple drop and swap...
I have a 2002 Yamaha VX200TLRA on a 2002 ChampioN 193. I have ordered a new set of the Yamaha digital multifunction gauges appropriate for my year model. The old analog gauges are reading...
I just had to come up with one of these myself. Crowley Marine can get them. www.texasoutboards.com has them. I just bought a used one off of ebay for MUCH less than a reman with no core. I...
I have a HPDI lower unit off of a 2005 VZ250TLRD that I might be willing to part with....
It will need to be put back together but all of the parts are there.
It worked! Launched my boat ans cranked up. Tell-tale had a very week stream. Allowed engine to idle for a few minutes to warm up. Made pass up and down lake at full throttle. Tell-tale is now...
I changed the poppet valve in my 2002 VX200TLRA OX66 yesterday. When I reassembled the valve, the spring and poppet got slightly twisted and is not straight on the sealing grommet. When I take it...
I had a 2004 H56 with a Yamaha four stroke 115 give me that same problem. The dealer found that it had jumped a tooth on the timing belt. Once the timing belt had been replaced, it ran good. It...
I have an 8" slidemaster manual that came off of my 193 when I went hydraulic. PM me and I will make you a good deal to get it out of my garage...
Try www.domednumbers.com They make custom decals. I just got trough replacing the decals and registration numbers on my 193 and they look great.
for those of us without facebook, can we get contact phone numbers etc.?
I agree with Pat. Safe-Floor is definitely the way to go. I just had a small area on the front of my boat done where the trolling motor mounts and everyone steps in from the bank. Was very...