I did my annual servicing yesterday and when I drained my oil I noticed a hint of that dreaded milky tint to my oil. The only thing I did was run my engine for about 10 minutes before changing it to...
Type: Posts; User: fishnhunt
I did my annual servicing yesterday and when I drained my oil I noticed a hint of that dreaded milky tint to my oil. The only thing I did was run my engine for about 10 minutes before changing it to...
Thanks for the replies...does anyone know if they make 1/2” wide carpet trim? All I can find is 1/4”. If I can find 1/2” problem solved however I have looked online and can not locate it. If someone...
I am replacing the carpet in my boat and accidently cut the bottom section of the floor about 1/4" too short on about a 2' section (where it meets the trim). I really do not want to rip it up and...
I just flashed my sho to a 300 from a 250 using hydrotecs flash. Just to clear some things up on gas, speaking to hydrotec, they told me specifically that you can run 89octane gas with a flashed SHO...
fiberglass the whole fender where the holes/cracks are and then hurculiner the fender. I did this to my iclass and love it. $200 job.
TX still on with potential storm?
SHO Just replaced mine gained 2mph
Trokars points roll on me after a couple fish.
With the VMAX Sho prop so hard to find, I was able to find a powertech VMAX3 prop in the pitch I need. Is this a carbon copy of the VMAX SHO prop? Should it run the same as the VMAX SHO prop or would...
Coming up to my 20hr service. I have a question my manual states: Recommended gear oil grade: SAE 80W API GL-5 / SAE 90 API GL-5….So Can I use Quicksilver High Performance SAE 90 gear lube in my...
Thanks for the input it looks like a wot run for an HR will possible fix my issue I'll give it a shot. Last question can I hurt the engine by running it with a little gas in oil if i am below top...
What is yalls suggestion on getting 6,000rpms? I am running a 25p vmx sho prop and running 72 @ 5700-5800 rpms water psi at 15 and rooster tail cowling height sidemaster jackplate on 8 dot. Based on...
So I purchased a 2016 SHO new two wks. ago. Motor is awesome besides the making oil part. I am at 10hrs and here is what I did to break it in. First two hours ran it up to 2,000 rpms varying rpms....
mike gerald
Thanks for the response. Did yall have to do any adjusting of the cables or was it a simple hook up and go? No Link and Sync?
I am repowering with a sho 250 going from an HPDI 250. I would like to rig it myself; however, I have never done it before and not really sure how a sho hooks up compared to a HPDI. I can figure out...
I will try that sat I do not know. I do know it doesn't die on muffs only when in the water with back pressure...
So I have once agian developed a issue I can't seem to pin down. At initial startup my motor will die every single time unless I put it in gear and give it some gas via hotfoot. The weird thing is...
weird...I have th same motor same year as yours all I did was unbolt the bolts on the jackplate that hold the PP mounting braket on...No taking the motor off?
the nine ponder went into cabelas fish tank
SYNCHRONIZING THE THROTTLE VALVES
If the throttle is operating properly there is NO reason to perform this adjustment. Un-necessary tampering usually just leads to performance problems....
Ok so I went and did everything I could and still have a low idle in neutral idle in gear. I link and sync the throttle plates - were fine from beginning, tps is set at 0.62 volts, new plugs, all...
How do I adjust my in gear RPM on a Yamaha hpdi 250? My tps is set at 0.62volts and idles around 600-700rpms in neutral, throttle body plates are sync and I get WOT with hot foot pressed. When I put...
I redid mine using cutting board Teflon from walmart I used a dremel and grinder to cut the steps out and then fiberglassed from the inside and outside on all steps I then used herculiner to cover...
Funny because I am in the process of redoing mine or trying too. All mine are cracked in the bends of the steps and the steps themselves are all broke. I took them off this weekend and I am planning...