Search:

Type: Posts; User: Kzaker

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    221

    I was just told that this is for a 4 Stroke, the...

    I was just told that this is for a 4 Stroke, the top of the shaft has two sets of splines. Is there anywhere that I can find bolt patters or any other identifying characteristics?
  2. Replies
    2
    Views
    202

    Thanks again:)

    Thanks again:)
  3. Replies
    4
    Views
    221

    Thank you, EuropeanAM, what’s the difference...

    Thank you,
    EuropeanAM, what’s the difference between the lowers for the mid Optimax vs the 4Strokes?


    Maybe I’ll dissect it as a learning tool.
  4. Replies
    4
    Views
    221

    Help ID mercury lower unit

    I picked this lower unit up from a guy closing his shop. He said it was from a 200 Merc but after looking on line for references, I’m beginning to think it may be from a smaller 90-115 HP opti,...
  5. Thread: posting Photos

    by Kzaker
    Replies
    6
    Views
    277

    If you use an iPhone, download the PhotoShrinker...

    If you use an iPhone, download the PhotoShrinker app, works great for this forum
  6. Replies
    2
    Views
    202

    Help ID lower unit

    Picked this up from a guy closing shop. Said it’s a Merc 200 outboard but I know it won’t fit my 2000 200EFI. Is there anyone who can tell by the shape/ bolt pattern what this is off of? 2.5l or...
  7. Replies
    5
    Views
    227

    Still troubleshooting this.. the tach apparently...

    Still troubleshooting this.. the tach apparently only does it while the motor is running- I’m not exactly sure why that is.. with ignition on and dash on, tach stays at 0
  8. Replies
    5
    Views
    227

    Thank you. I will check again as I believe you...

    Thank you. I will check again as I believe you had just made a note in my previous post to connect engine terminals first, then largest to smallest, which I have done.

    Under NORMAL conditions,...
  9. Replies
    5
    Views
    227

    Tach pegs 10 when trim is used

    OT153924
    200EFI.
    Just replaced the regulators with new oem, I’ve never had this issue before but I always had a bad regulator so I’m not exactly sure where I would be crossing/shorting. Doesn’t...
  10. Replies
    9
    Views
    951

    That was a task! All done, something at the bow...

    That was a task! All done, something at the bow was messed up: chop it all off and installed new color coded tinned wire and shrink wrapped them all up. Never would have started but ordered led...
  11. Replies
    9
    Views
    951

    So... when the switch is on nav, ONLY the nav...

    So... when the switch is on nav, ONLY the nav light should be active:correct? And same for anchor? Never both at the same switch position??
  12. Replies
    9
    Views
    951

    Yeah- I have the front nav light with the switch...

    Yeah- I have the front nav light with the switch and white light. I think I may have something crossed there. Reason I think it’s the white bow power is that EVERYTHING is on when switch is off. The...
  13. Replies
    9
    Views
    951

    Skeeter: nav anchor light, strange issue

    As I have never done anything to this circuit on the boat but for some reason; when I turn switch to anchor: the anchor and nav lights are activated. When on nav: only the anchor light comes on......
  14. I just chucked up the correct hole saw, cut...

    I just chucked up the correct hole saw, cut through plywood a few times then stacked the cores on the pilot bit. The cores were exactly same size as original hole and worked perfect to guide the...
  15. Thread: plug wires

    by Kzaker
    Replies
    8
    Views
    473

    Thanks for the wires Jay, good taking with ya...

    Thanks for the wires Jay, good taking with ya buddy.
  16. Replies
    10
    Views
    418

    Sorry, no, I ordered elsewhere but that was a...

    Sorry, no, I ordered elsewhere but that was a quick reference to the same part number when I put it in the google search bar. But I did make sure that I ordered NEW OEM parts. And thank you SO much...
  17. Replies
    10
    Views
    418

    http://www.bbcboards.net/attachment.php?attachment...

    http://www.bbcboards.net/attachment.php?attachmentid=339872&stc=1I believe I found it now in the schematic.. was looking at a 1999 diagram and it wasn’t there( or at least that I could see). I’ll...
  18. Replies
    10
    Views
    418

    When I looked up the SN, I came up with this...

    When I looked up the SN, I came up with this part: 883072T2 (apologies)<EDIT- Please read the Forum Announcements. We do not support parts purchased from Ebay.>

    Ill know for sure when they...
  19. Replies
    10
    Views
    418

    I am ordering 2 new regulators tonight. One has a...

    I am ordering 2 new regulators tonight. One has a hole blown through the insulation so I’m going to assume that’s at least the start of any repair if it isn’t the extent of the damage. I see some...
  20. Replies
    3
    Views
    174

    Thanks. I have read that these motor without...

    Thanks. I have read that these motor without alternators are not designed to handle the stress of optima AGM’s and everything I read tells me the same thing. I hate to buy another battery since that...
  21. Replies
    10
    Views
    418

    2000 Mercury 200 EFI regulator meltdown

    I posted in electric forum then figured I’d probinly get more specific answers here so:

    I have the above motor (SN: OT153942). The charging has never worked since I owned the motor (last year). I...
  22. Replies
    3
    Views
    174

    2000 Merc 200 EFI melted rectifier

    I have the above motor (SN: OT153942). The charging has never worked since I owned the motor (last year). I haven’t needed to additional charge but want to get it fixed. The battery, when charged is...
  23. No. Removed the original and took it to a welding...

    No. Removed the original and took it to a welding shop and had them weld an alum nut on the bottom. Now I’m having a hell of a time keeping the bolts tight to the floor- keep snapping the bolts off....
  24. What about this:...

    What about this:
    http://www.bbcboards.net/attachment.php?attachmentid=333988&stc=1
    38 diodes total on a 20amp circuit should be ok, I’d think?


    No comment
  25. Somehow I figured I’d reach the conclusion that...

    Somehow I figured I’d reach the conclusion that just going with the 7pin into a j-box and connection block would eliminate any second guessing (like above). It seems to be the simplest solution at...
Results 1 to 25 of 205
Page 1 of 9 1 2 3 4