I have owned many boats before and the motor gets trimmed as I increase speed. Not a trim issue. Looking for options for a new prop.
Type: Posts; User: cndbass
I have owned many boats before and the motor gets trimmed as I increase speed. Not a trim issue. Looking for options for a new prop.
Factory WOT RPM range 5500-6000
Had the boat out again last evening. Trimmed the motor up and gained a few MPH and got the RPM up to 5200. The boat is riding smooth and gets on plane quickly and is hitting 43 MPH (GPS) at 5200...
Yes WOT
The prop is what came on the motor. The motor is brand new. Aluminum 3 blade 13.2 x 19.
Currently sitting at 44mph at 4700 RPM
Good Day,
i am am a new boat owner and looking to upgrade my aluminum prop. The motor is 2018 Evinrude 90 HO on 17’ Smokercraft. Hoping someone can help me with. SS prop recommendation.
...
I have a battery switch installed but require a kill Switch lanyard for small tournament and for safety
So my boat did not come with a kill switch and I am looking to install one. Nothing two complicated, simple 2 wire switch. Attached is a picture of my ignition switch. The motor is a 2018 90HO....
So my boat did not come with a kill Switch and I would like one installed. Looking to install a simple 2 wire simple switch.
Attached is a picture of my key ignition wiring and not sure where to...
Here is mine. I am replacing the carpet and have access to the underside because of the extra storage compartment upfront so the cutting was easy. I added a bit of support under the pan to...
Here are a few more pictures. After of the rear deck when it was cleaned and the lid that have been cleaned but not yet primed.105673105672
So I now that the snow has finally melted, I was able to start the carpet replacement on my 96 18DXC. Luckily for me the carpet was original and came off in one piece and did not leave much glue...
Yes you are correct there is a compartment to the right of the pedal and there is also a drip rail on all compartments. Thanks for all you comments. I will post the carpet replacement, trolling...
I have a 1996 Astro 18DCX and am getting ready to replace my carpet and thought while it was off I would install a recessed trolling motor pan. However I have a few concerns with deck compartments...
I am getting ready to replace my carpet and thought while it was off I would install a recessed trolling motor pan. However I have a few concerns with deck compartments around my trolling motor. ...
As the main question is about the cranking amps for the motor I thought I would post here. Once I understand that I will request info on the batteries. I have few guys in my local club who are very...
Good Afternoon, I have a 1997 Merc XRI 150 and am replacing the batteries and need some help with the cranking amps. I will be replacing with Everstart and not sure of the sizing. Hopefully someone...
Thanks for the information. I have the boat nicely covered and the motor has been dropped and prop removed and greased. Do I leave the prop off and bag it or put it back on once greased. With...
I am looking to replace my cranking battery as my existing one is done. What I currently have is Optima Blue Top 34DC, MCA870, CCA750, AH55, RC120 and feel that it might not be large enough for my...
it is my first winter owning my Astro and have a few questions about winterizing it for the season. I live in Canada and the weather gets extremely cold and a ton of snow. I had the motor...
Found the bulb you recommended. Installed and all is good. Thanks again Don.
There are two tanks. I let one run empty and the other near empty, filled up today and each tank is 22 gallons. Mr RiverRatMD was correct. Thanks again everyone.
Thanks for the part numbers. I went to my local marina and the only bulb they had was part # 8M0054314. Will this bulb work for my engine or should I have them order the part number you listed...
I am looking to replace the bulb and associated fuel lines for my 1997 Mercury 150 XRI. I want to replace with Mercury parts and can't find the part number. Hopefully someone can help.
Thanks,