Search:

Type: Posts; User: JoeFriday

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 49 minute(s) ago.

  1. It could be oil weight. When I did mine, I...

    It could be oil weight. When I did mine, I remember it took forever to get all the air out and it working right.
  2. Replies
    9
    Views
    594

    I’m running a pump from these guys. No issues....

    I’m running a pump from these guys. No issues. https://www.highflowfuel.com/reviews/
  3. If they relay is going, it will do it again at...

    If they relay is going, it will do it again at some random point. When mine went, it was real intermittent. The last time, I was lining up someone to tow me back to the ramp when it fired. I hauled...
  4. Yup. Random no starts can be the fuel pump relay.

    Yup. Random no starts can be the fuel pump relay.
  5. There should be orings around the injector shaft...

    There should be orings around the injector shaft to seal them. The person cleaning them should have replaced them if they are thorough
  6. Replies
    5
    Views
    297

    That’s where I would start. You can’t run the...

    That’s where I would start. You can’t run the motor while using that flush port. Pull the screens on the lower intake too to see if crud is coming out.
  7. Replies
    6
    Views
    188

    If you’ve never replaced the low pressure pumps,...

    If you’ve never replaced the low pressure pumps, they are a maintenance item. I did the electric pump mod and removed mine. Pump self primes, so that lets you remove the primer bulb which is...
  8. Replies
    6
    Views
    188

    What’s the maintenance history? Weird stuff can...

    What’s the maintenance history? Weird stuff can have an electrical connection. Without knowing something about the maintenance, it’s a shot in the dark.
  9. Replies
    19
    Views
    899

    Since you mention the tilt deal, I wonder if...

    Since you mention the tilt deal, I wonder if maybe the float in you VST is out of whack. I still would check all the grounds. When those get corrosion, the symptoms get weird.
  10. Replies
    15
    Views
    1,044

    Just fine. No issues so far. For around $30, you...

    Just fine. No issues so far. For around $30, you can just replace every 1-2 years as preventative maintenance.
  11. Replies
    15
    Views
    1,044

    Yes. Running the Walbro pump on the motor. I...

    Yes. Running the Walbro pump on the motor. I built a harness adapter for the O2, so I can now run the NGK or Denso one.
  12. Replies
    15
    Views
    1,044

    Just running this back to the top in case someone...

    Just running this back to the top in case someone else is chasing gremlins. Boat has run probably the best ever. With everything I did trying to find the problem, I’m seeing the best holeshot and...
  13. Replies
    10
    Views
    368

    Change the impeller housing while you are at it....

    Change the impeller housing while you are at it. They get worn over time and will lose pressure. Had the same issue on mine. Poppet didn’t fix it, but the housing did.
  14. Replies
    2
    Views
    290

    I mounted the Walbro FRB13-2 on the motor.

    I mounted the Walbro FRB13-2 on the motor.
  15. Replies
    1
    Views
    218

    Check your grounds on the top, rear port side of...

    Check your grounds on the top, rear port side of the motor. My HP pump was sporadically dropping off, and corrosion there was the cause. Also, if you didn't clean the tube that feeds the O2 sensor...
  16. Replies
    19
    Views
    899

    Have you done the low pressure fuel pump delete? ...

    Have you done the low pressure fuel pump delete? I used the Walbro and mounted it on the motor. That was worth the effort.
  17. Replies
    19
    Views
    899

    Check the wires grounded on the rear top port...

    Check the wires grounded on the rear top port side of the motor. Mine had corrosion and it had a lot of weird symptoms.
  18. Replies
    4
    Views
    365

    There are two main things I learned doing mine....

    There are two main things I learned doing mine. Getting the main carrier bearing out is a pita, and replace every seal the first time.

    Got the carrier out with a gear puller and propane torch....
  19. Replies
    13
    Views
    581

    If the case isn’t damaged, rebuild it. They are...

    If the case isn’t damaged, rebuild it. They are not overly complex, but the carrier bearing can be a bear to get out.
  20. Replies
    4
    Views
    392

    Chris is great. If you have questions, just call...

    Chris is great. If you have questions, just call him. I ran ideas by him, and he let me know the best way to do the swap. I called him before and after I bought his reeds.
  21. Replies
    4
    Views
    392

    CC reeds come with the intake stuffers and are...

    CC reeds come with the intake stuffers and are priced for a little more. They are the real deal and make a difference. The power band builds much quicker with them.
  22. Replies
    15
    Views
    1,044

    Today was full lake test day. Holy cr@p. Boat...

    Today was full lake test day. Holy cr@p. Boat probably runs the best it ever has. The hole shot and 0-50mph is incredible. Big fan of the Chris Carson reeds now that I can see what they can do. ...
  23. Replies
    15
    Views
    1,044

    Original reeds that were over 22 years old were...

    Original reeds that were over 22 years old were perfect. Little sign of wear and probably would have lasted for the life of the motor, but you never know.
  24. Replies
    5
    Views
    569

    Check the poppet valve on the back low rear of...

    Check the poppet valve on the back low rear of the engine. If you got trash in the system and that is stuck open, it could impact your water pressure which would mean nothing out of the witness hole.
  25. Replies
    15
    Views
    1,044

    Chasing Gremlins in the Ox66

    I have the VX200TRLY. Let me start by saying that this motor has been rock solid for the 8 years I've had it. I did have the main relay go out and regular maintenance items, but nothing too...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4