Search:

This is the best stuff I've found. Been using it for years !! On Amazon !!

Remove the lid from the boat. Drill out the existing rivet heads and punch the remaining part into the lid. Drill the hinge and lid with a 1/4" drill and then install the hinge using 1/4" x 1/2"...

That depends on what you want to put back on. If you want a sleeve like is on there now, you have to disconnect ALL the wires and feed them thru the new sleeve. I cut the whole sleeve off, (using a...

Could be, check the fluid level, fill if necessary, and try again !

Top off the Master Cylinder and have someone pump the brake, like bleeding them, while you are under the trailer with a flashlight and look for the leak.

Well, I’ll be Damned !! Just got an email from them saying my shipment is on the way !!!

Not sure on the Ghost, but it's always been advised to disconnect the Trolling Motor when charging the Batteries. Either unplugging or using a switch or breaker to disconnect, that way if an...

20 some years ago, I had a partner that we fished 2 different Team Circuits. We switched off using each other boat. The way we worked it, Fill the tanks on both truck and boat before the tournament...

Go to a Pool Supply store and get the O-Ring Grease for on the Filter O-Ring. I lube mine every 5-6 Months. Stays on !!

A 220 outlet should be a different configuration. I'd check the outlet with a volt meter to see tho. Let the chargers rest for an hour of two, then try them in a different outlet that you know is...

Is it in the stowed position or the deployed position ? Mounted or just on the ground ? You may have to push DOWN on the mount and then pull on the cord.

Unfortunately this is what I'm finding out !! I thought they were a reliable company !

Try using 2 3/8's oz A-Rigs hooked together end to end for a bigger profile and added weight to take it down deeper and keep it there.

I've fished Shasta many times and use a Tex-posed 6" Roboworm Morning Dawn on a #2.0 EWG with 12# Fluro leader. You just have to Finess it thru the trees, but need the 12# to drag them out !! Love...

I use a Shin knot for Braid to Fluro Leader and cut it to be twice the rod length. Then re-tie when the Knot is just outside of the tip.

Level the trailer unhooked, then measure from ground to the top of the hitch. Whatever that measurement is, that's what you want the top of the ball on the tow vehicle to be. Depending on your...

C & E Boat Restorations, England, Arkansas 870 575-3948 Curtis Massey He does AMAZING work !! I live in Fresno, Ca and when I get to where I need new carpet, I'm gonna drag it from Ca to...

My trailer is 2014 duel axle with Vault hubs and has never leaked or squeaked !! I carry a grease gun and a dead blow hammer. Should I have an issue, I'll pop off the cap, fill the hub with grease...

Place a light coat of RV-BLACK Silicone on the outside of the cap before you install it with or without an "O" ring. It will form an excess at the front of the cap as it goes in, do not wipe it off....

You should start by leveling the trailer tongue off of the vehicle. Then measure from the ground to the top if the hitch. What ever that measurement is is the height you want the ball on the tow...

Try hooking it directly to a battery, not a buss bar. It sounds like there are too many things hooked up to the buss bar. If it still flashes then contact Garmin.

I made an order a month ago and received a conformation and a note that there were some delays in shipping and they would let me know when it ships. Well, today I tried to send them an email to the...

Did you mount it on the motor or on the shaft ? If on the shaft, is it facing front to back and not side to side ?

Was the old plug a flat plug or a round plug, and how many pins ?

I've heard you can replace the whole relay setup with a $20 Wench relay from Am....... !