So put a gauge on boat and ran it. Boat has 35.5 with key on / not running. Boat idling 32-34. Boat running its 32-34 runs great, then it wavers and drops to nothing, killing engine of course. I...
Type: Posts; User: Mwbmod74
So put a gauge on boat and ran it. Boat has 35.5 with key on / not running. Boat idling 32-34. Boat running its 32-34 runs great, then it wavers and drops to nothing, killing engine of course. I...
So put fuel psi gauge on boat it'll idle all day at 35.5psi It jumps out on top running good then after bout 3/4 mile or so the fuel psi just drops and that's when it'll kill engine.
And I have a automotive fuel injection test gauge but I do not have the correct schraeder valve adapter for it. Anyone know the correct size??
The boat has the new mercury line grey with blue writing on it from tank to motor, in the last year. How do you do a test on pulse pump??
OT430883 02 Pro XB 250 Motor runs great, boat jumps on top lots of power, runs bout 1/2 mile then just shuts down, you can barely feel any sputtering at all. You can pull it in neutral, she...
Another update:
Pressured system up to 6psi at hose where it connects to the crank case check valve, and the system works as it should. It fills the engine tank, loosen cap a bit and oil comes...
Update on oil issue.
I put a new crankcase check valve in, still wont push oil to engine tank. I checked my pickup screen, its clean, I put new o rings in my remote tank, still wont push oil to...
02 Mercury Pro XB 250 - OT430883
I have the intermittent 4 beep horn which im assuming is the low oil alarm. I put a new sending unit in engine oil tank, still does it, read on here to try to...
I ground paint off one of the bolt holes on the ign module put a star washer behind the bolt and grounded it to the top bolt that has the cannon plug holder. my existing ground wires were on the...
Ok so I checked all my connections and plugs, and all seem tight and clean, so when you say add a separate ground ground from ign module to the block, is there a stud on the ign module to do so? If...
02 Mercury 250 Pro XB OT430883
Boat has set since summer and it set a bit before that,,,, fuel was treated, issue is, boat runs great up to 40-45 MPH, but if you start pressing it say you trim her...
I just put new cables on my ULTREX, how much tension is suppose to be on these?? I didnt get crazy just snug, but figured id ask.... Thanks in advance!
Mine just snapped a cable, now granted my Ultrex was one of the first ones and its been used a lot, so I dont guess I can complain too much other than im at Rayburn for the week with a broke TM....
Ser # OT430883 02 Mercury Pro XB250
I all of the sudden lost all power to my key switch, trims, and gauges dont activate when key is turned "on"
I loaded the boat trimmed motor up put support on...
I all the sudden have no power to my key switch or my trim switches and my gauges dont activate. The lights on gauges and all pumps and everything else works as it should on the boat. It is a 03...
Im posting this for a buddy, I don't have the required info far as serial number. But he is in a special bind. His 16 G2 200 put a Code 214 / steering pump pressure sensor low / service soon message...
I built aluminum airboats and other aluminum rigs for years.. The right way to fix that is not a goofy screw and mallet... It is a build flaw at vexus... The deck needs the carpet removed drill...
Except for the 10 rods hanging DIRECTLY over said tackle....
Can you get one without that grab handle?? I just thought I didn't like Bass Cats grab handle, this is definitely a turn off... Everything else is good though. But if you don't remember to put...
OK I have to ask just so im clear on what to tell him to try, and pardon me because im completely ignorant to the gel coat spraying deal. So your saying to get some PVA put ONLY PVA in the gun and...
He used a brand called Johnson Fiberglass and Resin Inc. He had a gallon of clear gel coat resin, then a gallon of Prestec High Gloss additive. That Prestec stuff says it has the wax already in it. ...
My nephew sprayed clear gel on his half solid / flake boat. They for some reason did NOT do a test panel (fender) but sprayed the entire top cap and the gel fish eyed and has not 100% fully cured...
Im in need of a new transducer for my front 1198. My current one has the down / side / 2d, I think its a XTM 9 HDSI 180. Was wondering if there is a different transducer that would work better on...
Yes im aware this is not normal. As I originally stated I set this thing up in early April, and its been rock solid until last trip out. And this thing gets used about 2-3 times a week, so its got a...
No the light stays steady red but sometimes blinks super fast.