Search:

There is a T fitting have way between the livewell and the transom. There’s no easy way to get to it without disassembling the whole rear of the boat. If that’s leaking. You have to pull the carpet...

430079 430080 430081Well the brackets weigh less then the jackplate I used to have.
With my setup, it’s still less than just a 75hp motor.

If you get maintenance free AGM Duel battery (deep cycle and cranking) it will be just fine with the stator charging system.
i’ve been running one for three years with no issues at all. It only...

Use a beard trimmer. You can continue to set it closer and closer for a shorter cut as needed. I re-carpeted my boat with 16 ounce carpet. And I had to trim every hatch down eighth of an inch on the...

I chose to go with poles and not spot-lock, for the reasons mentioned above. I fish more shallow water rivers now more the deep lakes. They both have their place.
429085 429086

3M 77 super spray adhesive. Very easy to use and once it’s down it ain’t coming up.

Second hole down from top. On motor to transom mount. Cav plate is 1” up from bottom of keel. Can’t remember off the top of my head. The measurement. But I think it’s about 6-1/2”

Dude, you have no VST tank. They took the VST take out that runs the high-pressure fuel pump inside of it for the fuel injection on the EFI you have exact same motor I have. That is the wildest thing...

13p Trophy Sport, 36 gps / 38 gps with worked 3 blade 14p
My boat is much heavier then a stock boat. But the weight is set in with my rebuild to maximize bow lift.

I tow a 175 with a Frontier 4x4. It really tows great. My truck is a 2017, pretty good size disc brakes all around. Remember you have a 4.0 V6. But you also have a frame that is a lot like a Titan...

I had a 95 Silverado 4.3, pulled 20’ and 19’ glass boats. No issues. I believe it was rated 7k to 8k back then. It will do fine.

426040
Well mine will be different for sure. I took out the 21 gal tank and had a 11 gal tank built. It is snug. But there are 2 pole pumps side by side. 3 batteries, charger. I can get more pics...

425230 You can see my is on the port side wall

Hey, where your drive shaft leaves the Motor cowling and goes into the top of the lower uint. There is a black plastic washer on top of the pivot housing. See if it has popped out and slapping around...

:thumb up2:

Iam currently running Roy’s old rims and tires. The M8008’s are still in great shape. But I will be changing them this winter due to age. Not because of wear.

Yes on the trophy. If you go with the spitfire, I would go with a 14p. I tried a 13p years ago when they first came out. Insane! Holeshot, but rpms was pegging 6000 at half throttle. If your only...

I always index the spark plugs. It could be that simple. You want to torque the spark plugs to the motor Specs. But in doing so if it takes another eighth of a turn or quarter of a turn to get the...

Definitely add more cup.

415933 Well, another picture. Roy says they look awful tall. But they work really great.
Ho and no The prop is a experiment. It’s a 12 1/2 pitch with a lot of cup at it. You can actually see the cup...

In the spitfire, go with the 14p. But yes you can’t beat a 13p trophy sport.

I would get the same size pitch prop you have now. In a aluminum Spitfire prop.

Get a 13p Trophy Sport issue gone.:thumb up2:

:thumb up2: 415328415329415335Well took me a while. But there on. And trying them out for the first time tomorrow.
Yes I remove the jackplate. And with just the brackets on for the last couple of...

Contact a local weld shop, that can weld aluminum. Around here that’s about 50-100 dollars. Easy to fix.