lets make this a little more simple. I have a y cable one side is side imaging and the other side is dual beam. the side imaging goes to the transducer that came with Helix 12 chirp si on the...
Type: Posts; User: ewailes82
lets make this a little more simple. I have a y cable one side is side imaging and the other side is dual beam. the side imaging goes to the transducer that came with Helix 12 chirp si on the...
i currently have a helix 12 chirp si unit and looking to add a helix 12 chirp di unit.
how would i set up transducers and units. (plan on having a 2d thru hull)(would like to have crystal di and...
Thanks so im starting to get some where. So if i got a helix 10 chirp di gn2 and mounted the di ducer on tm. do i just hook up the 12 chirp si to the network and use the 2d and di off of 10 in...
so what would happen if i plug the di transducer from 10 into 12 and just run mapping on 10
so i have a helix 12 chirp si gps gen1 and a helix 10 di gps gen 1 . im wanting to put both graphs at bow. i would like to have have chirp 2d and di only. which transducer should i use?
I think i got the answers needed. thanks guys
Current graphs
bow helix 12 chirp si KVD transducer on TM
console helix 12 chirp si KVD transducer on jack plate
looking to add
bow helix 10 chirp gps (only going to hook up power cable and...
what do you mean by dedicated DI?
on the Helix 10 chirp unit will it then have DI and SI as well? ( i think i saw my helix 10 gen 1 do this but not read cause of chirp) Is that correct?
dont care...
First let me lay out my setup and what im looking for.
console= Helix 12 chirp si kvd (hd transducer mounted on jack plate and 2d mounted on transome low to get depth while running)
...
My question is will the DI transducer (xnt 9 DI T) work on a HELIX 12 CHIRP SI unit. i understand that side imaging wouldnt work but im installing it on the bow so i dont really need SI. still want...
Checked the poppit valve. Didnt seem to be stuck open. Cleaned it up and put back together. When checking that I think I might have come across the problem. Found a temp wire shorted out to the...
replaced both temp sensors. didnt correct problem. when problem occured again checked oil reservior on motor and was full. is there a water line or something i can check to see if i have sucked up...
ive never replaced strainer. ive had the boat for only 5 years. next time im out and it happens i will check oil reserve. but im starting with the temp sensors talked about in previous quote. i think...
I tested both sensors. Hooked each sensor up to a seperate multi meter to test continuity. Place them in a pan of water along with a temp probe. Turned on oven and tested to see if i had a sensor...
2002 YAMAHA OX66 225HP Alarm going off at anywhere between idle and wide open. If i dont touch hot foot at all its fine. If i run it wide open its seems fine. Alarms sounds after minute or 2 on all...
What pitch? What diameter? Is this a 4 blade?
What pitch? What diameter? Is this a 4 blade
Was wondering if anybody is running a 4 blade prop for rough water and if so what props are good. When I say rough water I mean Great Lakes rough. What prop are the great lakes guys running if not a...
in search of a dash panel for 2002 zx225
anybody know where the sensor is located?
I have a 2002 skeeter zx225 with 2002 yamaha vmax 225hp ox66. My overheat alarm is sounding off and light up before even starting motor. The last time I used it had no problems. Today when I went to...
I have a 2002 ZX225 with a 12"slidemaster jackplate and was wondering what brakets I will need if installing 2 8' blade power poles?
Thanks for the help!!!
New Pal Bassmaster club tournament
You can take the u bolt part of the lock and install it in either side. One way activates the alarm and the other acts as just a pad lock.....very clever design....wouldnt do it any other way
Its fall time now and we all know that spinner baits and buzz baits are a big tool us anglers use in the fall to catch those mean green fish we all love. If you have never heard of Red Dirt Bait...