If you have smart craft gauges/wiring - It could be the wiring for the remote oil tank sensor. Your tank may not have the level sensor installed.
Type: Posts; User: yupitsme
If you have smart craft gauges/wiring - It could be the wiring for the remote oil tank sensor. Your tank may not have the level sensor installed.
Take the batteries out. Transport them to the house and charge them there. There is no real good option for charging the batteries sans a reliable electric source. Or... portable generator powering a...
check the hull for damage. May have to jack it up a bit to clear the bunks if initial inspection does not reveal anything.
able to run on high(or higher) setting without damaging the motor.
The conversation here is about an Outlaw hull. An Outlaw hull does not a 209 make. As we discussed in an earlier conversation - get your p-2-p right then start trying to dial in the 27p Trophy plugs....
One, larger of the two, appears to be an HDI transducer. Should work with any HDS head unit. Might work with elite series as well but someone else will have to sound off on that issue.
The...
I'm puttin' my money on "The Debil did it!"
Is the back lighting level the same on both units? The amount of "draw" the unit has directly impacts the voltage reading of that unit. Also if you have more/different transducers this can impact the...
"IF" it's epoxy adhesive at heat gun, not a hair dryer, will soften it up making it possible to remove with a sharp scraper. A heat lamp can have the same effect but takes a tad longer. Just use...
Navionics has a "Easy View" menu selection that significantly enlarges the waypoint icon/name.
:thumb up2:
7/8" bore brush. Chuck it up in a drill motor. Be sure to vacuum hole when done - $6
528356
...
On all but the rarest of occasions: "The teacher learns more than the student." Good teachers that is.
You are correct!
Mmmm... no. When a warranty claim is honored and a new unit shipped the warranty clock does not reset. If you had, say, 8 months remaining on the original purchase - you'll have 8 months remaining on...
Mmmmm.... How can the Elite "flash and shut off..." when the Elite isn't even powered up - If you powered up the AT first and let it stabilize before powering up the Elite as recommended?
If the...
Run temp power cables for the Elite fs direct to battery. Then power up AT and see if issue is still present. Or.... if you have the ability to power the AT on first. Let the AT boot all the way up...
Probably low voltage caused when the AT starts up. Could be battery but most likely wiring is the issue. Insufficient ga wiring to carry all that's on that particular circuit...
Mangled indeed! :laugh::beers:
https://images.contentstack.io/v3/assets/bltab8525fe5f7bb21b/blta327779ea2171ea4/63bf67294933ee68391a0276/SMG11HD_ProductImage_PrimaryImage_1500.jpg?width=1280&quality=75&auto=webp
FEATURES AND...
Your steering input is countering natural and unavoidable prop torque. It does not matter if you have cable or hydraulic steering the prop torque is there. When you cut the throttle prop torque goes...
Do you have a Stealth 1 charging system? And actually... that ground wire is connected to, or should be, the #1 trolling battery wired in series. You can tell the #1 battery in a series - it's the...
Just as a test... Reconnect the old Point 1 and see if it works now. You might end up with a spare Point 1. You don't have to re-install it. Just see if it's visible on the NMEA network.
Annnd... My instructor said "When the plane clears the ground you will experience prop torque to the left. Counter it with right rudder!" Sho'nuff... wheels cleared the runway. Prop torque to the...
I got cardboard boxes - big ones. Cut them up to the shape LxWxH to fit the ProTour I was shipping to a buyer. You have to make the bottom and the top to go over it. Once you have the bottom made get...