Search:

Type: Posts; User: Cray

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    1,973

    Biggest thing I know of on the older Pd motors is...

    Biggest thing I know of on the older Pd motors is the foot pedal switches are usually pretty iffy. Look up co called Northlandmarine. Call those guys and they will be more than glad to answer your...
  2. Call this place and talk to Jason. You can get...

    Call this place and talk to Jason. You can get new style main board and new style pedal for around 200.00. If you find the old style it's going to be used and probably not last long. Just went...
  3. Thread: Kamato Joe

    by Cray
    Replies
    24
    Views
    3,337

    I bought a Visions large professional series from...

    I bought a Visions large professional series from Home Depot for around 700.00 Sams has one called a Bseries for 549.00 compare very well to GE and joe. Actually much cheaper because it comes with...
  4. I have done them both ways in my master built....

    I have done them both ways in my master built. Can’t tell 2 cents worth of difference. Do mine at 225 and only one tube of chips.
  5. Replies
    14
    Views
    830

    http://www.crappie.com/crappie/off-topic-in-missis...

    http://www.crappie.com/crappie/off-topic-in-mississippi/365695-crappie-fillets-air-fryer/

    this is may help with fish.

    here one forchicken...
  6. Thread: down to 2

    by Cray
    Replies
    11
    Views
    3,180

    Freightliner dealership's take care of them....

    Freightliner dealership's take care of them. Friend has one and has over 50,000 on it and not one problem.
  7. Thread: Rain Suit

    by Cray
    Replies
    22
    Views
    4,928

    I just did a bunch of reading on this subject....

    I just did a bunch of reading on this subject. GoreTex says wash on gentle cycle alone with a mild liquid detergent. Dry on a low setting or let dry on it's own. Then put in the dryer alone on...
  8. Replies
    3
    Views
    1,256

    A company in Georgia or Alabama I think builds...

    A company in Georgia or Alabama I think builds one called a Royal. Really nice looking boats. Seem to be well built.
  9. Replies
    14
    Views
    900

    I can see where he could knock out a bunch of...

    I can see where he could knock out a bunch of jigs at one time with that setup.
  10. Thread: wind issue

    by Cray
    Replies
    5
    Views
    358

    To make your rudder, try to find and old broke...

    To make your rudder, try to find and old broke hand control troller with metal shaft. Remove motor, split shaft down the center and find a piece of aluminum plate to make your rudder. Slide plate...
  11. Looks to be Owner add on. If factory it would be...

    Looks to be Owner add on. If factory it would be on the dash with rest of switches. Probably going to have to just pull on some wires and trace it out.
  12. My 04- FL 50 was doing about the same thing....

    My 04- FL 50 was doing about the same thing. Couldn't figure it out and finally replaced plugs and haven't had a problem since. One was completely dead. It will also cause them to make oil.
  13. Thread: F90 troubles

    by Cray
    Replies
    5
    Views
    163

    If it in fact sucked up some mud, you could very...

    If it in fact sucked up some mud, you could very well have some in the thermostat causing it not to open completely. Find and pull the thermostat. Flush back through the passages and blow out real...
  14. Thread: Rebel sqaure bill

    by Cray
    Replies
    17
    Views
    937

    I have one just like that in a box somewhere. I'd...

    I have one just like that in a box somewhere. I'd say late 70's very early 80's.
  15. Replies
    41
    Views
    1,786

    Like bilgerat stated. Take the pump off and have...

    Like bilgerat stated. Take the pump off and have it rebuilt, only if you figure out how to set it before removing. Pump is oil lubricated and should be timed to the cam or crank. Shaft seal bad...
  16. Replies
    7
    Views
    629

    If you go to stainless and it still porpsie's try...

    If you go to stainless and it still porpsie's try a set of trim wedges. Thick part to top and it will give you a few more degrees negative trim which some times helps.
  17. Replies
    46
    Views
    2,880

    Jigalow sent PM

    Jigalow sent PM
  18. Replies
    13
    Views
    2,024

    If a change to Stainless prop dosn't help try a...

    If a change to Stainless prop dosn't help try a set of trim wedges to get you some more negative trim. It seems some of theses tin boats have to much angle built into the transom.
  19. Thread: 22 LR ?

    by Cray
    Replies
    15
    Views
    407

    I have looked around N Ms and Memphis for 3 wks...

    I have looked around N Ms and Memphis for 3 wks and can't find any at all. One gun shop had 1 box of short rat shot. It's nuts out there.
  20. Replies
    31
    Views
    3,201

    Really nice boat. You need to be really proud of...

    Really nice boat. You need to be really proud of it. We need more young Men with your discipline today.
  21. Thread: Crappie setup?

    by Cray
    Replies
    10
    Views
    2,036

    Sea Ark builds a 18 crappie specific that is...

    Sea Ark builds a 18 crappie specific that is wider on the front deck than the Predator with all the features any other crappie specific boat has. I fish out of a WarEagle 17.9 stick steer and in my...
  22. Replies
    1,942
    Views
    212,099

    Sticky: US Navy ENC. 1965-1979 wish I was still in.

    US Navy ENC. 1965-1979 wish I was still in.
  23. Check NAPA or one of the tool trucks. They do...

    Check NAPA or one of the tool trucks. They do make and sell a half moon tool just for driving out races. Going in Brass,Brass. And always wear safety glasses.
Results 1 to 23 of 23