When I had my boat, I only put ethanol free gasoline in it even tho the manual said blended gases were fine.
As for my automobiles, Costco it is as its the cheapest around and its also Top Tier.
Type: Posts; User: cfm56doc
When I had my boat, I only put ethanol free gasoline in it even tho the manual said blended gases were fine.
As for my automobiles, Costco it is as its the cheapest around and its also Top Tier.
When I had my Ranger, I would put it on the passenger side by the grab handle with net end down. I would then take the rod strap and run it over the handle of the net and it worked great for...
Unbolt it from the bracket leaving the hoses hooked up and lay it across your rear deck (recommend laying a blanket down on your deck first). Once out of the garage you can bolt it back up.
Do you have a hot foot? If so, make sure its not from that. Mine had the spring tensioner adjusting nut back off so I had to lift up with my toes to get the engine to idle back down.
Try pouring some water into the holes you drilled and see if it goes to the bilge area and that will answer your question about draining.
For those with a Z118, I just posted two engraved seat plugs for sale.
http://www.bbcboards.net/showthread.php?t=1067434&p=11224981#post11224981
Mods, feel free to delete as the manual has been sold.
I ran a fish tape and then attached a piece of twine to the fish tape. The twine was long enough so that when I pulled the fish tape back out, it actually left two lengths of twine in the wiring...
In my experience with 303, if you keep it dry it looks good, but if it rains, you will see where it is washing off as it leaves streaks down your boat. Don't believe me, try a little on your car...
Engine exhaust comes out the prop center. If you put oil in the cylinders and motored the engine over, then most likely this oil at the prop is nothing more than the oil you put in the cylinders and...
Search my post as I added the tool holder from a Nitro as it had a corner cutout that worked perfect for keeping the TM cable off the fwd plotter. I think it was like $26 including the cup holder...
Thanks, that is what I was thinking as well.
Follow up question, do the dual consoles use a different cover than the single consoles? Looking online at other brand covers it appears they use the...
Sorry, he actually has a 2003 518 comanche.
Let me ask him again as I am sure he has a 2006 518 comanche.
I recently sold my 2013 Z118 and I still have the factory boat cover (never used). A buddy of mine has a 2006 518C and I was wondering if my cover will fit his boat? Both are single consoles, but I...
If you were closer I have a garage kept 2013 Z118 I would sell you for a great price.
Good luck and this is a great smaller platform!
Are you just in need of pictures of the wires to the ignition switch? If so I can try to take pictures of my 2013's.
Guessing OP is not the original owner as I thought it would have been covered.
I use Eagle One wax as you dry. Stayed away from Bass Boat Saver as I read it can ruin plotter screens should any accidentally get on your screens. Eagle one there is no fears of ruining my screens.
Not the same boat or engine size, but my 2013 came with a Merc 4s
Here is what I did on my 2013 Z118. I measured the TM tray opening and then went and measured the holder for the new Nitro boats. The new holder is about an inch too wide so I cut an inch off and...
I have done best on Winterset and Lulu, but still tough.
Not sure I can help you, but my 150 stays nearly vertical due to space and zero leaks.
I hear you, but they would have to throw NOTHING at it. And IMHO anyone turning down 3k profit is a fool.
And dealr giving me 24 does not mean the dealer needs to sell to a boat dealer for 24...