Search:

I'm dealing with the same problem with the same motor. I was fishing and put it on 100% and it died. After about 10 minutes, I could run on 20%. Not the batteries. Just replaced them yesterday...

I have a 2000 225ox66. I had a new oil pump by chance, changed it, so that rules it out.

i am not getting oil from the remote tank in the boat to the tank on the motor. The emergency fill...

I have a 2000 model Yamaha OX66 225. When I shift it into gear I get an knocking sound as the prop rotates. Take it out of gear it stops. The prop has no slack in it. It is tight. Anyone...

489946

I have a Yamaha225 ox66 2000 model. I need to know what a part is called. It is the little pad the two trim rods hit when the motor comes down and first makes contact. I noticed they had a bolt...

Been having trolling motor interference on my graph. It happened on a garmin and lowrance. I have been trying to read all the possibilities to fix this. I started with a dedicated line. Before...

Thank you. It makes sense now that it has been explained. Lol

So I just need to unhook one of the wires and delete a breaker? Thank you!

If this is not allowed on the Champion Boat section since it involves a Champion, Delete. I posted in the trolling motor section, but thought I might get a quicker answer from this section.

I...

I just purchased a new to me 36 volt trolling motor changing from a 24v. My plug has 2 positive cables and 1 negative. I have 2 - 40 amp breakers at the batteries. On the breaker panel, it has...

Going from a motorguide 80 to a 112 fortrex.

I am switching from a 24v to 36v trolling motor. Is an extra jumper all I need to do when adding the 3rd battery? What else do I need to look at?

Had to put on a new jack plate and I am trying to get the boat set back up. I have a 2000 model Yamaha ox66 225. I do not know the minimum water pressure for this motor. I know as you raise your...

Thanks.

When measuring the motor for height, do you get the trailer level or the boat topcap level? I get different measurements either way. Which is correct?

I may have it to deep. Mine is set up where it is maxed out when the trim stops. I don’t work the trim for a sweet spot. That is how it was set up when I got it and just left it that way 20 years...

Ok. Took it off the boat this morning. Have it boxed and ready to ship. Didn’t know if I needed to run it first to see what it did so I could describe what it did on my boat.

I have a Champion 203 with a Yamaha 225. Both were manufactured in 2000. Just put a 10 inch rapid jack on it after it was rebuilt. Trying to set it up. I have it now running 70 with a M27 Yamaha...

To get the 26 pitch tempest worked for a Champion 203, who is the best to send it to. I have heard both are good, but who is recommended mostly for the tempest work. What is the usual cost?

I plan to send it off to get worked.

Thanks. I got a steal. $285. Was on a motor that blew a piston 4 years ago. Said it only had about 20 hrs on it and has not ever been worked.

Just purchased a 26 tempest plus off ebay. My set up is a 2000 champ 203, 225 Yamaha ox66. Will I need a blowout ring with this prop? I have not gotten the prop yet, just need to know if I need to...

Thank you. I guess I have to make a purchase.

I have an older 73sv. Can anyone tell me if Lake Darbonne in Farmerville, Louisiana has been updated to show a complete map of the lake? My Garmin only shows the lake with the channel. No markings...

Anyone ever use 5 star for trim repair? If so, what is your opinion. 2000 ox66 Yamaha 225.