Search:

Type: Posts; User: DaleHollar1

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    239
    Views
    37,610

    Has anyone tried one of these? They are standard...

    Has anyone tried one of these? They are standard on older carb vehicles after they did away with mechanical fuel pumps so I figured they would last a lot longer.
    ...
  2. Replies
    18
    Views
    1,841

    No way it’s not hurting Yamaha. It’s like saying...

    No way it’s not hurting Yamaha. It’s like saying every store is out of your product but selling your competitions brand. But hey we will get to feel shelves again one day. Wrong, you lost a lot of...
  3. Replies
    13
    Views
    448

    What two plugs look different?

    What two plugs look different?
  4. Replies
    12
    Views
    603

    Didnt take 30 minutes to pull the powerhead. Yes...

    Didnt take 30 minutes to pull the powerhead. Yes we applied rtv around the water jacket holes when putting heads back on. I don’t know what part number he got on the impeller.
  5. Replies
    12
    Views
    603

    I got there after he ran it so he may have had...

    I got there after he ran it so he may have had water to high. We pulled the head powerhead and his gasket should be here today or tomorrow. We will try it when we get it back together. If that...
  6. Replies
    12
    Views
    603

    Yes. Has a strong stream but not much comes out...

    Yes. Has a strong stream but not much comes out up at thermostat. We started it with thermostat out. All we could get was what looked like exhaust smoke. But we did have lower unit in a tub. Think we...
  7. Replies
    12
    Views
    603

    94 150 Johnson overheating

    Hello everyone,

    My nephew has a 150 Johnson that is overheating. He just bought the boat and the guy he bought it from hooked it to a hose and ran motor for a few minutes before he bought it....
  8. Does the buzzer go off after you sit for a few...

    Does the buzzer go off after you sit for a few minutes? I’m gonna bet it’s your filter on the oil reservoir in the boat. Pull the reservoir out of bracket and lay on its side. The filter is on the...
  9. Replies
    7
    Views
    1,227

    I have a 225 hpdi or ox66 I’ll sale you.

    I have a 225 hpdi or ox66 I’ll sale you.
  10. Replies
    7
    Views
    1,489

    Looks like fish jacking bait up.

    Looks like fish jacking bait up.
  11. Replies
    5
    Views
    745

    You can get a total rebuild kit for around...

    You can get a total rebuild kit for around 14-1500 bucks. You will need to send injectors off to be cleaned and calibrated. And then block work would be your only other thing. Probably for less then...
  12. Replies
    24
    Views
    2,839

    You can tighten the steering by turning wheel all...

    You can tighten the steering by turning wheel all the way to one side then pull the wheel as hard as you can that way. Turn it opposite way and crank on it. Do this several times back and forth....
  13. Thread: Prop slip?

    by DaleHollar1
    Replies
    3
    Views
    358

    Sounds like you need the vacuum fuel pumps on...

    Sounds like you need the vacuum fuel pumps on side of motor changed
  14. Replies
    6
    Views
    848

    You could take the hubs to a machine shop and...

    You could take the hubs to a machine shop and have them drill and tap the backside of hub for a grease fitting. You would need it tapped right between rear race and seal. All the benefits of drilled...
  15. Replies
    4
    Views
    622

    97Triton, you should have called MFI in...

    97Triton,
    you should have called MFI in Winchester TN. I called them and they built mine while I was driving there. Had me fixed up. They are the ones who built our trailers. Didn't have to measure...
  16. Replies
    10
    Views
    497

    Pull the cap back off. Clean the inside of the...

    Pull the cap back off. Clean the inside of the hub a little then with a small screwdriver feel around about a 1/4 inch inside the hub for a small groove. I think they may have started using the seal...
  17. Replies
    6
    Views
    510

    You can find the a60 if that's what you have in...

    You can find the a60 if that's what you have in the 140 range.
  18. Replies
    4
    Views
    276

    The new inner will come with a break away cable....

    The new inner will come with a break away cable. It will have everything on it. You don't need the solenoid. Most drums trailers have free backing shoes. If you have 10 inch which is proabbaly what...
  19. Replies
    0
    Views
    119

    Helix 7 do problems

    My helix 7 has stop showing depth today. Was working fine a week ago. Went fishing today and not showing any depth. Checked wires and cord and they are all cosmetically fine. Hooked to my helix 7 si...
  20. What was your WOT rpms?

    What was your WOT rpms?
  21. Night fishing is here!!!!

    Night fishing is here!!!!
  22. Replies
    236
    Views
    31,781

    Triton should give you a new hull and a new...

    Triton should give you a new hull and a new motor. Most of your motor warranty has expired sitting in there factory. I have a 97 Triton Tr21 and have started to sell it a few times but can't let go...
  23. Replies
    6
    Views
    387

    Sorry, I saw hpdi and missed the year model.

    Sorry, I saw hpdi and missed the year model.
  24. Replies
    10
    Views
    615

    Make sure you don't have water leaking somewhere...

    Make sure you don't have water leaking somewhere in the cowl. If you do when you hit a wave it will bounce water into your intake and make it run bad until it clears out. Then you will regain rpms.
  25. Replies
    6
    Views
    387

    You maybe cheaper in the long run to install...

    You maybe cheaper in the long run to install command link gauges. It's one set of wires ran to the motor. I installed one not long ago and love it.
Results 1 to 25 of 219
Page 1 of 9 1 2 3 4