Glad that it wasn't too bad to rewire. Don't forget to enable sync in the settings under system/power control (I show that in the video). Hopefully all goes well. And I got the sync video up this...
Type: Posts; User: GarryW
Glad that it wasn't too bad to rewire. Don't forget to enable sync in the settings under system/power control (I show that in the video). Hopefully all goes well. And I got the sync video up this...
If you use connect the blue from the AT2 and the yellow from the Pro and enable sync then that is the only function for the yellow wire from the Pro unit. So you will have to a few options to enable...
If you connect the blue from the AT2 power cord to the yellow on the Pro unit AND enable sync in the settings on the Pro, then it will eliminate virtually all of the noise interference. I have done...
The Evinrudes that I have had idle around 500 rpm and max out well below 6100 rpm. I would suspect that your analog gauge is off. The data coming on the NMEA bus interface comes straight from the EMM...
Also, if you add the AT2 and a Pro unit then you can sync them together to significantly reduce screen noise.
The NMEA bus doesn't draw much power and is fused at 3 Amps. You should be able to power it from the bus blocks in the console area. The Rangers that I have wired usually have the NMEA bus powered in...
That's interesting, when I've installed that interface for people and configured their units (Lowrance, Humminbird) I've never had to check any boxes in the Device's data list. And I've never had to...
Do you have another transducer turned on? That's what it looks like to me. Lowering the contrast will definitely help. If you have a Pro unit running the transducer then you can setup the Sync...
I use Gun Oil that I got from Bass Pro. It seems to keep the noise down for about a month, then another shot of oil. I oil all of the bushings. And yes, check the base plate bolts and the two screws...
Go to Settings/Network/Device List. Scroll down until you see the Yamaha EMM (it may be called something else but it should obvious). Then click on the Data button on the bottom right. You will see...
I recently installed a Cornfield Live Sweep on a Ranger 621. He has a Terrova on the boat. I did a video on it if you would like to see one installed on the Terrova. He is water testing it now. And...
Actually Simrad units the capability to turn them all on when one is powered up. I would suspect that they would do the reverse, i.e. shut one down and they all shut down. The Simrad software is very...
Thanks, I'm trying to share a bunch of how-to stuff for folks, much of it is based on questions that I get asked directly or see asked on the message boards.
Actually, the gateway was the...
If you look under the bilge area lid, there should be a wiring diagram. The ACC bow switch is the orange wire with a blue stripe. I don't have my boat handy to look but in the picture that I have of...
To get the Mercury icon on the left part of the screen you will need to get the Vessel View Link module. The mobile version only connects to your phone while the Link and the Gateway connect to the...
I run the C-MAP Discover chip. It has good detail and coverage for the river and lake. I also have a C-MAP Reveal Eastern but it only partially covers the river and lake (US side only). So I end up...
I used food grade silicone to lubricate the O-rings. I've had no issues.
You should have room in your bow on a Skeeter to place a fuse block there. You can mount the block using doubled sided 3M permanent tape directly to the hull on the starboard side. You'll be able to...
When I install power wiring, I usually pull 2 (two) 8 gauge duplex wires. One to the bow and the other to the console. They are connected on the positive side to a breaker (usually a 30 Amp) mounted...
Yes Lowrance makes an extension cable for the transducer, it is 10' long. Part number: 000-16069-001.
You need to use either the VesselView Link (link is in the prior post) or the VesselView gateway. You will need a junction box to connect to the SmartCraft network. Your boat probably already has one...
It only supports the Halo dome radars. (Sources: From the user manual and from the internal training.)
If you look under My Files, check each directory to see where the space is being used. Perhaps you have Sonar logs there. If not then check the other directories, from the dialog something the My...
I have used Gun Oil, that I picked up at Bass Pro Shops, on all of the bearings. That seems to help stop the creaking. It will last for 3-4 months. I have a 60" so there is more stress than a 47"...
I just rigged a boat with 2 NEP boxes, 5 HDS Live units (3 bow, 2 console), 2 Active Targets, and a XM-4 module. I have the same issue. When everything is connected as it should be then I lose...