I have been running a Fury 3 25p as most are sold with and have gotten it up to 75 solo a few times but now one of the blades are bent and I can't get 70. All that said, I wanted to go to a 4 blade...
Type: Posts; User: texashawgs
I have been running a Fury 3 25p as most are sold with and have gotten it up to 75 solo a few times but now one of the blades are bent and I can't get 70. All that said, I wanted to go to a 4 blade...
I just found that it was the engine power fuse (15 amp one) inside the cowling on the motor. Guess I'll run a separate wire from the fuse box for the hydraulic sensor gauge tomorrow since that is...
Anyone know what I may have pulled or something when I ran a transducer cable through to the console? I checked the yellow w/red stripe wire and it's still connected (came undone before). Only other...
Try that motor up another 1". I have the 21PHX and it runs great between 2.5 and 2.75". 2.5 with me and 2.75 with 2 or more. Time in the seat means a bunch since I've never had to 'drive' my previous...
I have seen no bashing other than other fisherman bashing themselves for not buying a Phoenix as good looking and good riding as my 2018 21 PHX. :nanner:
Wsbruton, if you are in Oklahoma, check out Fun-N-Sun in Hurst, Texas. They know these boats well and can make you a great deal. I should know. I am now on Prostaff for them and Phoenix. I am driving...
2018 21 PHX
Mercury Pro 250XS
25p Fury
Bob's Action 12" Hydroplate
1 12' Talon
36v Ultrex 112 60" (will cut down)
4 31 batteries
Best speed so far after just breaking her in: 72 at 5600 rpm...
The 921 PHX has higher gunnels and a deeper profile. I just ordered one because I like to be dry and I like the gunnels to be high so my rods don't easily fly over when I have a bunch on the front...
Thanks Alan...
Looking to get a new front trailer axle for my tandem axle trailer. I tried calling Ezloader but they couldn't even tell me the specs on it after looking up the actual trailer. Crazy. Anyone know the...
What was the price on that boat?
You have to take the panel in front of the batteries out to get to them. They can be easily replaced. Might think about replacing them with LEDs as well. Enjoy...
Anyone have the best motor height for this boat? I have mine at 2.5" below pad and have a 25p Tempest Plus and only getting 68+ mph at 5750 rpm. Is the motor too high? I've got a 10" manual jackplate...
Steering is still not solid in the middle running over 60. When sitting still I hear popping while turning the wheel. Maybe the helm is bad? Can it go bad? I put in more steering fluid by turning the...
Didn't think about a transducer causing that. I have had this same transducer mounted at the same spot on my other Cobra hulls and it didn't seem to make a difference on those but maybe this is...
It's not a chine walk though. Never seen or heard of a chine walk in a Cobra boat. This is my 5th one. It just tries to jump to the right or left when trying to keep it straight like the steering is...
When I get up in speed in my 216 Cobra with Mercury 250xs, it seems the boat doesn't want to stay straight, it constantly will pop to the right or left. When I keep it turned a shade right or left...
just did. thanks don for any help...
I have a merc 250xs racing version and sometimes while out on the water running, my motor will act like it's running out of gas and just cut on and off till it stops completely. After pumping the...
I noticed some leaking on my trim assembly when getting out of the water the other day and after closer inspection, I found a hole on the very top of the left side of the assembly. Had to look back...
I think I know the one. Found a coil plate diagram and it shows where it connects to the engine below the coil plate as you stated. I followed a tube all the way around the engine that I think may be...
Anyone know where this tube comes from the engine to hook up to the console panel? I can't seem to locate it to connect. A diagram would be nice but I can't seem to find one online. I don't like...
The engine was completely submerged in fresh water. I cannot get a spark and technicians in my area are all way too busy to help unless I was rich. I think the computer is gone because I was at least...
Need a list of things to do and how to get a spark going to fire it up. I heard the wiring harness is usually toast when going under water. Any thoughts on by-passing the harness to get power to the...
750 lbs I believe