Search:

The size of the breaker is determined by the wire size and length of the wire. Charts are available online to tell you what you need. I used a 40 amp breaker at the battery that serves as a cutoff...

My stabilization quit working and my compass will not calibrate now. They must have something to do with each other.

I put fuse panel and black box on the board in the back of the rod locker. Worked great to take the board out for the install and then put back in.

I have the 126 on the bow and 106 at the helm. I ran 8 awg positive and neg from battery to blue sea fuse panel mounted to the board in the back of the rod locker. I also mounted the gls 10 to the...

Mk - 330D came in my 2015 618.

I purchased from them for a new boat and they were great. Moved to another state and ordered the new numbers and they were not the same size. No problem they sent me the original size and received...

If it’s right you should be able to straddle the trailer and pick the boat up with considerable effort and clear the roller. The roller should not support the boat. You want just enough weight on the...

I have the same set up. The sleep mode operates independently. When I change spots I put the bow to sleep and do the same thing with the console after the move.

No, they sleep independently of each other. I didn’t think I would like the auto on and off feature when I installed mine but I do now.

The rubber washers don’t go on the 34. They go on the 32. My 34 came with the rubber washers . I called Garmin and the tech verified that they belong on the 32 and should not be in the box.

You are probably in too deep. The short bunks just barely out of the water should be about right . You can tell if you need shims by picking up on the front of the boat with considerable effort and...

I’m new to Garmin but on my last units changing to a different megahertz helped more than anything

I bought the dual screen shroud from Tim at the plant. Looks good and cheaper than the mounts you buy for the old shroud.

If it’s a small spot I would use the contact cement. Whatever you use don’t use to much. It will bleed through the carpet and you will have a mess.

I ordered at 4am Friday My 12 in has shipped and the 10 in is still in process.

I got one a couple of weeks ago from Marinemaster for $31.68 which was a lot better deal than anything on Amazon . The shipping added another $20 but it was still the best price I could find.

I wouldn’t spray the whole bunk just the front third which is where the wear probably is. I would not unhook the boat until I was in the water and hook it before pulling out after spraying . You will...

It’s normal for an Optimax to turn over slow the first crank of the day. After that it should pop right off. Has to do with the compressor building pressure before allowing the engine to crank

Johnny has Carbon 12’s on sale for $1499 . What’s up with that ? I thought they were discontinued a couple of years ago. Must have found a couple of pallets in the warehouse.

My Hamby light has been on 5 years right below bottom wing . No problems.

Thanks Don. The serial number is the first thing written. 2b178647

2b178647 130 hours on Bennington pontoon. I purchased the boat at one year old. It has a Yamaha 10 micron fuel / water separating filter that I assume was installed by Bennington. The primary filter...

I have a Reese locking ball and I had to grind a couple of the edges to allow the coupler to latch. I would think if it did latch it might not unlatch. I expected the ball to be hardened but it was...

If you need to shim you need them on the front two bunk supports. When you shim just the front the trailer crossmember will bend rather than raising the boat up. It’s a group effort to hold the boat...

I have not done it yet but here’s my plan. Run 8awg wire from battery to blue sea 40 amp breaker in bilge and then to a blue sea fuse panel in the front of the starboard rod locker. From there to...