Search:

Type: Posts; User: Scott S.

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    211

    It's not compatable. Yank the merc stuff out and...

    It's not compatable. Yank the merc stuff out and put the OMC stuff in. It really isn't hard, just takes time. When you pull the merc stuff out, tie ar heavy string, or small diameter rope o the end,...
  2. Replies
    5
    Views
    464

    Straight gel requires a Bink 2001 or a 2100 with...

    Straight gel requires a Bink 2001 or a 2100 with a 68bp tip. If you want to spray gel like paint get some Dura Tech Additive.You can look it up on youtube, it sprays like paint. Styrene is a bit...
  3. Replies
    2
    Views
    280

    exposed edge of the lid?????/ The carpet should...

    exposed edge of the lid?????/ The carpet should rap the lid, nothing is exposed other that the back of the lid, and in most cases it should be powder coated, but that will flake off over time, or...
  4. Replies
    4
    Views
    360

    2" from the edge, a good sharp razor blade, Don't...

    2" from the edge, a good sharp razor blade, Don't cheap out on the blades, get a 50 pack and change after a few cuts, I go through 25-30 on a boat, clean crisp cuts matter.
  5. Replies
    4
    Views
    1,487

    Just look at the carpet, you should be able to...

    Just look at the carpet, you should be able to see the heads, or at a minimum the indendtation in the carpet. The ones by the seat, of they're still there will ne 3" long. Seat removal, not really,...
  6. Replies
    9
    Views
    570

    You want the weldwood in the blue and white can,...

    You want the weldwood in the blue and white can, Or find some birdsong.
  7. Replies
    13
    Views
    915

    Gel coat is a barrier for the glass, put gel coat...

    Gel coat is a barrier for the glass, put gel coat back on the boat. Get a quart of black gel and a quart of duratech addative, it turns thick gel to an air dry paint. Scuff it spray it, let dry for a...
  8. Replies
    2
    Views
    416

    Once the foam flotation has been compromised it's...

    Once the foam flotation has been compromised it's junk. Remove the floor and scrape/dig it out, replace with new 2 pound foam.
  9. Replies
    4
    Views
    284

    Metal cutting fine tooth.

    Metal cutting fine tooth.
  10. Replies
    8
    Views
    467

    FGCI has some of the best gel on the maket, spays...

    FGCI has some of the best gel on the maket, spays butter smooth, as in easy compaired to some shit that composite one sells. I told the Comp one salesman the the fgci gel come out of the gun better...
  11. Replies
    3
    Views
    310

    Get some double fold sunbrella, you can buy it by...

    Get some double fold sunbrella, you can buy it by the roll or the foot or yard. It will last longer tan the cover.
    ...
  12. Thread: Carpet

    by Scott S.
    Replies
    2
    Views
    306

    Rachford supply has the 16 oz. 16 is Not 20,...

    Rachford supply has the 16 oz. 16 is Not 20, there is a difference in thickness, side by side you can see it.
  13. acetone or take your womans nail polish remover,...

    acetone or take your womans nail polish remover, same chit.
  14. Replies
    4
    Views
    401

    Most rangers will locate the back side of the...

    Most rangers will locate the back side of the tray into the front compartment. My old POS FS had to have the front lie well cut down to get it to fit. I've built a few hundred and install a couple...
  15. Thread: loose carpet

    by Scott S.
    Replies
    3
    Views
    480

    Don't use that rubber Chit in a small can, it's...

    Don't use that rubber Chit in a small can, it's garbage.
  16. Replies
    9
    Views
    823

    Cut angles at the hinge, 45 minimum. Every other...

    Cut angles at the hinge, 45 minimum. Every other place cut it straight, cut those at an angle and you'll have big azz gaps.
  17. Ranger uses protech. I had to do some warrenty...

    Ranger uses protech. I had to do some warrenty work on a ranger several years ago, on a boat that they used shit padding on, they used the wrong pad on several model years. what they sent was...
  18. Replies
    16
    Views
    1,296

    It would be up to the builder to give the the...

    It would be up to the builder to give the the info needed. No one is going to measure a boat in hopes that it sells.
  19. Replies
    3
    Views
    507

    so you used it and liked it, use it again.

    so you used it and liked it, use it again.
  20. Replies
    10
    Views
    563

    You can pull one bolt and take a pick tp check...

    You can pull one bolt and take a pick tp check the transome core. Take a top one out and inspect, put it back in with rtv, pull a bottom bolt and reapeat. You only need to pull one top and one...
  21. Replies
    4
    Views
    434

    You can always paint it. I would find some...

    You can always paint it. I would find some plastic trim, 12' stick of extruded aluminum will cost you an arm and leg to ship.
  22. Replies
    5
    Views
    727

    Total boat make some good shiat, it will take out...

    Total boat make some good shiat, it will take out 600 grit and make it look like a mirror.
  23. Replies
    4
    Views
    434

    find some plastic trim, or some aluminum. Like...

    find some plastic trim, or some aluminum. Like this, but hunt down some plastic stuff, it will bend easier,...
  24. Replies
    5
    Views
    706

    You should scroll through the posts in this...

    You should scroll through the posts in this section, you would find you answer in 10-15 secounds.
  25. Replies
    5
    Views
    700

    You can get a gallon of white gel with wax on...

    You can get a gallon of white gel with wax on Amazon from Fiberglass supply, it was unser 50 bucks just before christmas. Brush it on or roll it out, don't spend 20 bucks on a gallon of acetone to...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4