Search:

any updates with this?

update: sent prop to mark and had PVS holes put in. before with gas and livewells full and a partner in the boat it would not get on plane and only turn 2100 rpm. ended up running just the holes with...

I have completely redone a 1998 triton TR18 repowered with a new yamaha 175 SHO. I started with a 23 pitch T2 prop and was a little too much. I went to a 22 T2 and all was good until I just put 2...

sorry yes razor 3. Ok so i took off the yamaha prop and put the razor on and i feel a slight drag turning the prop by hand. I don't hear anything rubbing and don't see anything rubbing but the yamaha...

I just repowered from an older 2-stroke Evinrude to a Yamaha 175 sho. Can I take my croxton razor 3 prop off the old Evinrude and make it work on the new Yamaha?

I've just bought a 2017 175 SHO and I'm having trouble finding the trim sending wire. Google has led me to believe that it is a orange wire but i cant find it anywhere. I see a white plug with a thin...

i am replacing reverse gear and shift clutch on a 1985 150hp. In the book it says that if you are replacing either forward or pinion gear that they have to be a matched set. It doesent say anything...

Mod. J90PLSTC. Sorry for the late response

a little history about motor. boat sat in garage for 2 years. before attempting to start I drained the fuel tank and the float bowls. gas didn't look terrible but did smell varnished. sprayed carb...

i have a few of the curado 200 e7 that the thumb (spool release) button is getting hard to push down especially if the spool is under any slight tension. I have upgraded most of the reels over time...

The one I'm looking at has tiller style trolling motor and no recess. Definitely want to switch to foot with recesse. Just don't want to hack up a new ranger

I've been looking into the intercostal but want to change to foot control with recessed pedal. Looking at pics it looks like there is a removable lid where the recess would go. Does anyone know if...

OK I'm going through the lower unit on my 150 and bought a set of cheap o snap ring pliers to pull the snap rings behind the bearing carrier and they bend right as you get close to getting it out. I...

I found a local 22 pitch raker that came off a 200hp Suzuki,I am wanting to put it on my evinrude 150 2 stroke with 15 spline and 3/4 x 16 prop nut. I forgot to ask him if his was a 2 or 4 stroke but...

can Someone give me the part numbers for the high compression heads on a 1985 OMC 150Hp

ueddate. I bought a manual checked the stator out and it was good so went ahead and bought a voltage regulator and that fix the problem thanks everyone for your help much appreciated

I am having the same problem, boat seems to run fine but I have been told that I have a bad stator. money is a little tight but hope to have new stator next week and I will post back when I have new...

Bummer. I already have close to 1 hour of break in time with it like this. Motor seems to run fine will it hurt to continue with this slow break in while I'm waiting for a new one and is this one of...

When you turn the key on it has 12vdc then when you start the motor it's 11.4 +/- .3 vdc. I checked it at the terminal strip on the motor and its the same.

yep I have all that

just rebuilt an 1985 150 model #j150tlcos it didn't have a tach so I added one and double checked that I have it on the right pulse setting. it works fine under 1000 rmp but when revved any higher it...

How much for a razor 3?

I am just about done on a 1985 evinrude 150 restore project thats going on a equally older 18' ranger. I have done some Internet research and looks like the majority says the original 24p raker is...

I am restoring an old Ranger and would like to make this 1985 run and look as new as possible. it is a VRO, model #E150TL. the compression is in the low 80's on all cylinders and would like to do a...

Another vote for the samurai