Mine recently had a little moisture build up inside the slots and stopped reading. Removed cards and cleaned them up, then lightly applied some PC duster indirectly towards the slots to avoid forcing...
Type: Posts; User: Missile Pilot
Mine recently had a little moisture build up inside the slots and stopped reading. Removed cards and cleaned them up, then lightly applied some PC duster indirectly towards the slots to avoid forcing...
Settings>Coord system>Decimal format. When you're done, you can change it back to whatever you had selected before or leave it in this format.
421796421797
Sounds like you can, just has to be an active 2D sonar input.
419989
If you could draw us a simplified one-line diagram of your network it might help, especially if removing a terminator allowed network discovery. Sounds like your terminator(s) aren't on the "ends" of...
Glad you got it figured out, and more so for the follow-up. I, nor most battery testing locations I would think, would not test the battery off both the primary post AND the screw on post. So...
You're not in 3D chart view are you? If 3D is selected, the chart common functions are different.
So when you restored primary power, If you press and hold the power key no audible beep? Do you have another unit connected via ethernet cable?
As far as trim reading, I believe mine shows similar. I'll check tomorrow. For the other engine info, you just need to set up the Instruments screen with the data you want displayed, similar to...
Well there appears to be a way to do it, but it's a little technical and not sure how the system would respond after making changes and saving "Settings.set" then uploading on SD card and importing...
Chart Options>Categories>"Look for something here under the dropdown that corresponds to Obstructions" Not sure of which sub-level selection has these (Chart Base Data maybe?) as I'm not at my unit...
Yeah I guess that's a possibility, but I hate to make a claim for what seems like a minor issue. If the impact had been more substantial I would be all over the insurance for sure, but we barely felt...
GPS Position out to a VHF is one possible output. The end of the manual list all the 2000 and 0183 Input/Output data. And no it doesn't need to be grounded, only the primary ground for your power...
Recently hit something submerged running about 40mph with a VMAX 250, no damage to boat or prop just lost a chunk of the skeg. Circled back and was unable to locate anything in my path, and water...
Not only is the imaging improved overall, the display is easily viewed with polarized sunglasses from all angles. I no longer have to bob around depending on where I'm standing on the boat to get a...
Do you have your menu set to auto-hide? If so, I've experienced similar while exporting regions of waypoints. So I draw my target area box and then make a slight adjustment such as dragging the...
Well there is one option, that could probably be simplified but I don't have the time to script something in Python (maybe?) but if you export your waypoints as GPX file, open file with WordPad,...
I just went thru this last November timeframe. Run and die. Could pump the bulb and keep it running. Fuel Feed Pump fuse was blown, replaced it, started engine and it blew the fuse again. Could still...
Unless you plan on trolling motor mount for second 3n1, I wouldn't install both on transom. You don't want to run the same frequencies that close together, and you'll have a replacement 3n1 for later...
If it's popping and clicking when you turn the wheel then it sounds like you have air in the system. If so you'll need to bleed the air, but I recommend you have some fluid on hand to replenish if...
Ensure whichever download you selected is placed on the SD card which will be used in the assigned device. So whatever the names of your units on Insight must match the unit and SD card. The NOS...
I did get my second one sometime after my first, though it was all submitted at the same time. I'll have to go back and read the print myself as I missed that. Definitely cleaned up the color shading...
Not to high-jack the original post, but mine occurred prior to the update and hasn't returned following the update.
I had same happen few weeks back, submitted a problem report after the reboot and was contacted from Lowrance troubleshooting almost 3 weeks later with direction to call them for troubleshooting....
Placed my rebate order on 5/13 and finally received my card today. So about a month wait. It still shows processing on the rebate tracking page, and I'm waiting on second card for second unit.
If you have a large number of waypoints and have them backed up on SD card, I would Delete All followed by Purge on both units individually. If you have the two networked together and attempt this it...