It's not compatable. Yank the merc stuff out and put the OMC stuff in. It really isn't hard, just takes time. When you pull the merc stuff out, tie ar heavy string, or small diameter rope o the end,...
Type: Posts; User: Scott S.
It's not compatable. Yank the merc stuff out and put the OMC stuff in. It really isn't hard, just takes time. When you pull the merc stuff out, tie ar heavy string, or small diameter rope o the end,...
Straight gel requires a Bink 2001 or a 2100 with a 68bp tip. If you want to spray gel like paint get some Dura Tech Additive.You can look it up on youtube, it sprays like paint. Styrene is a bit...
exposed edge of the lid?????/ The carpet should rap the lid, nothing is exposed other that the back of the lid, and in most cases it should be powder coated, but that will flake off over time, or...
2" from the edge, a good sharp razor blade, Don't cheap out on the blades, get a 50 pack and change after a few cuts, I go through 25-30 on a boat, clean crisp cuts matter.
Just look at the carpet, you should be able to see the heads, or at a minimum the indendtation in the carpet. The ones by the seat, of they're still there will ne 3" long. Seat removal, not really,...
You want the weldwood in the blue and white can, Or find some birdsong.
Gel coat is a barrier for the glass, put gel coat back on the boat. Get a quart of black gel and a quart of duratech addative, it turns thick gel to an air dry paint. Scuff it spray it, let dry for a...
Once the foam flotation has been compromised it's junk. Remove the floor and scrape/dig it out, replace with new 2 pound foam.
Metal cutting fine tooth.
FGCI has some of the best gel on the maket, spays butter smooth, as in easy compaired to some shit that composite one sells. I told the Comp one salesman the the fgci gel come out of the gun better...
Get some double fold sunbrella, you can buy it by the roll or the foot or yard. It will last longer tan the cover.
...
Rachford supply has the 16 oz. 16 is Not 20, there is a difference in thickness, side by side you can see it.
acetone or take your womans nail polish remover, same chit.
Most rangers will locate the back side of the tray into the front compartment. My old POS FS had to have the front lie well cut down to get it to fit. I've built a few hundred and install a couple...
Don't use that rubber Chit in a small can, it's garbage.
Cut angles at the hinge, 45 minimum. Every other place cut it straight, cut those at an angle and you'll have big azz gaps.
Ranger uses protech. I had to do some warrenty work on a ranger several years ago, on a boat that they used shit padding on, they used the wrong pad on several model years. what they sent was...
It would be up to the builder to give the the info needed. No one is going to measure a boat in hopes that it sells.
so you used it and liked it, use it again.
You can pull one bolt and take a pick tp check the transome core. Take a top one out and inspect, put it back in with rtv, pull a bottom bolt and reapeat. You only need to pull one top and one...
You can always paint it. I would find some plastic trim, 12' stick of extruded aluminum will cost you an arm and leg to ship.
Total boat make some good shiat, it will take out 600 grit and make it look like a mirror.
find some plastic trim, or some aluminum. Like this, but hunt down some plastic stuff, it will bend easier,...
You should scroll through the posts in this section, you would find you answer in 10-15 secounds.
You can get a gallon of white gel with wax on Amazon from Fiberglass supply, it was unser 50 bucks just before christmas. Brush it on or roll it out, don't spend 20 bucks on a gallon of acetone to...