Has anybody had trouble with the Gambler trolling Motor foot pedal well being too small for the new trolling motors with spot lock?
Type: Posts; User: treehanger
Has anybody had trouble with the Gambler trolling Motor foot pedal well being too small for the new trolling motors with spot lock?
Crickets?????
Im looking to put a new Motorguide Tour Pro on my 99 Intimidator and was wandering if the foot pedal will fit the basin?
Yes and thanks and I had them checked a few months ago.
Ok looks like the IZFR5G is the plug i need. iv been running what is listed on my motor wich is the PZFR5F-11 which I can not get but a year out of a set.
I have a 1999 Mercury Optimax 200 hp serial# OG883983 and I need to Know what spark plg I need to run in this engine. My local dealership told me a NGK PZFR5F-11 OR A CHAMPION RC12MC4. Are these...
Ok thanks guys.
I tow my G with a tacoma and the brakes are neccessary. If you cant back your trailer without it locking sounds like your reverse solonoid in the tongue is not working.
I have the UFP db-42 and was wandering if there are any cross refs for pads I can get locally at an auto part store. I cant find any UFP pads locally. I need them quick. Thanks
Does anyone know if I can cross over the db-42 pads to a car pad that I can get local at an auto part store. I cant find the ufp Pads locally. and if so what do i cross them with.
Ok guys I have replaced the intake air sensor that was bad and both tpi sensors, ran the boat this afternoon and the motor ran smoother than ever before. I have had it 2 years and it was like silk...
Ok got me a service manual and it tells me I have a bad tpi. My engine only goes in alarm at 4000 rpms. So which tpi is bad the inside or outside. When we hooked to computer they both looked to be...
OK hooked back to computer and checked tps1 and tps2 they both went from .35 to 4.08 volts. they were opposite of each other. We also found the engine air sensor on front of the air handler was...
1999 200 Optimax serial og883983 Got an alarm when I press my hot foot to wot to come out of hole or any time i go wot. it is a intermittent beep and the engine lite and guardian mode engages. I took...
Ok guys I raised my motor a 1/2 inch and man what a difference, the boat handled much better but started loosing water pressure before I could get her trimmed enough. It would fluctuate about 10-15....
Ok so if I raise my motor will my lift come down a touch on the stern of the boat? I'm
going to try a 1/2 inch.
How will I know if the prop surfaces?
Just got my trophy 26 on my 2000 Intimidator and my motor to pad height is 4 3/8. I ran boat today and boat seemed to not handle well at high speed. almost like it had too much stern lift. I was...
what did you do with the repaired prop, did you get it worked out or replace it?
You would think they would want him to advertise because they not going to. Cool video though. Hope he just covered up the logos on the boat because he might have a hard time getting new ones.
I just had to get new lower unit replaced due to a good ole Coosa river rock. I'm running a 1999 2000 Intimidator with a Mercury 200 Opti. Im turning a 26 Tempest Plus Prop and it also got damaged....
I buy mine here in Alabama at Airport Marine in Calera for 28 bucks out the door.
Thanks guys for the imput, for you guys turning a 4 blade which brand is best for the 2000 Intimidator. I have a Trophy plus but it is the wrong pitch. Im going to sell it and buy something different.
I have a 99 2000 Intimidator with a 200 optimax turning a 26 tempesst plus prop when I get to about 5500 RPMs the rear of the boat feels like is takes a slide to the left. Im not sure what is...
It would have made better sense to put overflow out of back than front of livewell. But ok thanks guys.