Just a quick browse on Facebook Marketplace, Similar trolling motors are posted for $800-$1200. HDS units $500. I am sure I could sell the HDS for $100. Prop for $200. Thoughts on what to sell...
Type: Posts; User: guntherbluefin
Just a quick browse on Facebook Marketplace, Similar trolling motors are posted for $800-$1200. HDS units $500. I am sure I could sell the HDS for $100. Prop for $200. Thoughts on what to sell...
I have a 2000 Nitro 700LX. Condition is what you expect in a 24yr old boat. It does not take on water, transum is in good shape, trailer in good shape, brand new tires, 3 good batteries, 80lb Minn...
I would like to have Side Scan on my Dash unit. I would connect the proper transduce off the back of the boat.
If I network the Dash unit with the Front Unit, can I also see the side scan from...
I didn't install it yet because the wire colors don't match. The MERC part# is 883072T - The only OEM one I found is used on <Non-Supported Site Links> says it's a match.
Some years ago, the...
544900Good afternoon, I have a 2000 Merc 125hp 2-stroke. 0T018423 - 125ELPTO
I am trying to replace the rectifier hoping it's the cause of engine not turning off with key (it can turn off with...
Thanks
Hey all,
I need to replace all of my batteries. I have a 115 Opti (2013) - Ill have up to 2 Fishfinders... probably 9" and 5" - Chirp or Sidescan (no livescope), rarely use livewell.
I will be...
Thanks - cool feature but not worth the price.
I am trying to determine which to buy. I can't find a good side by side comparison. Minnkota does not answer the phone.
Things I want - 80lb, 45" shaft, Spot Lock, wired foot pedal (electronic...
I just got the Z6. Mix of Garmin and hummingbird that I need to figure out. My next boat will come with a new garage
The Z6 just barely fit in my garage. I bought it because the Z17 storage length is at least 12* longer
I am am getting a new'er boat. Looking at 2013 Nitro N6 and 2018 Nitro Z17. Not sure if I can get the Z17 to fit into my garage. Neither have good TMs or electronics.
I have the HDS9, but I don't think it's compatible with the Ghost..at least not fully feature compatible.. I'm early on in research, so I don't know everything each of them can do.
I am looking for a new Spot Lock trolling motor. Just the simple feature Spot Lock is most important. However I know there are numerous other features and they work best when you combine the brands...
I am upgrading my 700LX and needing something similar in size... Cant fit much bigger boat in my garage. I looked at a 2013 z6 (115 merc, 70lb trolling motor, ok GPS...), looks like good condition...
I read a few things about that, maybe there is an open in the switch to ground circuit. But for sure, kill switch stops, key does not.
I was experiencing sluggishness on holeshot and a few MPH below previous years. Marina thought the issue was plugs so they replaced them. No improvement. Then they said the boat is probably water...
I weighed the boat and trailer. I expected about 2500 lbs with full tank of gas and gear - 1153 Hull, 375 125hp, 400 trailer, 150 batteries, 50 trolling motor, 200 gear, 160 gas... it weighed in at...
Service tech thinks my 700LX is bogging on launch and a few miles/hr down (off top speed) because it's waterlogged. I am trying to find the weight specs. I called NITRO and hull is 1158 and they...
I still have a problem. I bought a replacement rev limiter from CDI. I installed it and tested the engine with water muffs on. It started fine but wouldn't turn off. I disconnected it,...
Thanks for the help
I disconnected BLK/yellow, purple, and brown. It fixed the issue but couldn't turn the engine off. Put them all back and disconnected one by one. Brown. What's the risk of leaving it disconnected
There are several wires. black/yellow that is split and goes to two separate location; purple; brown, black. Which ones do I disconnect?
I found the Rev limiter. 413964
Do you think the limiter is the defective part? Or some sensor telling the limiter to 'kick in'?
Hello all,
I have a strange issue with my Merc 125. Once I get to about 3000RPM, the engine cuts for about 1 second then kicks in for about 1 second, then cuts.....I can't keep it over 3000 RPM....