Search:

Type: Posts; User: JRBjr

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    11
    Views
    421

    You can do a search for rubber trim on Amazon and...

    You can do a search for rubber trim on Amazon and it will take you to it. Other sites have it as well. It is very common because it is used for so many applications.
  2. Replies
    11
    Views
    421

    Mine did the same thing. I ordered some of the...

    Mine did the same thing. I ordered some of the same trim from Amazon. It is a breeze to install and very inexpensive.
  3. Thanks to all who responded, I think I have found...

    Thanks to all who responded, I think I have found the answer to my question by your responses. I didn't think about all the issues involved and especially the interference. The way it is now, I...
  4. Running electronics from trolling motor batteries

    I have three 125 ah Ionic batteries which run my Ultrex. At the console I run a 15 inch Helix and a 12 inch Helix. At the bow there is a 12 inch Helix and a 10 inch Helix. All of them are...
  5. Replies
    43
    Views
    2,729

    It may have been Dewey Bain from Grenada...

    It may have been Dewey Bain from Grenada Mississippi. He later sold the ring worm to Rebel. I still have some of the original ring worms with "Bain" on the tails.
  6. Replies
    6
    Views
    405

    I know the transducer port is not bad because I...

    I know the transducer port is not bad because I have a mega down imaging transducer connected with a Y cable and I can get down imaging and 2D on the unit. I have also restored defaults twice and...
  7. Replies
    6
    Views
    405

    Yes I did that but it still won't recognize the...

    Yes I did that but it still won't recognize the 360. I moved the Helix 15 to the bow temporarily and the 12 to the console and at the console it as able to read the 360 off of the network but will...
  8. Replies
    6
    Views
    405

    Helix 12 DI G3N and 360 problems

    I recently had to take my Ultrex off for repairs. I took the Mega 360 off and laid it aside. When my motor was repaired, I put the 360 back on. From that point, my Helix 12 would not connect to...
  9. Replies
    7
    Views
    436

    I just went through the same thing. My trim was...

    I just went through the same thing. My trim was doing just as you described, 2012 SHO 250, ended up having to put a new trim motor on it. For several months it became slower and slower and at times...
  10. Replies
    25
    Views
    3,348

    I am anxious to know the answer to that question...

    I am anxious to know the answer to that question as well. In anticipation of the Mega 360, I updated to latest software on my Helix 12 3GN and it is doing the same thing. My DI transducer is...
  11. Replies
    1,516
    Views
    334,500

    Thanks Wayne

    Thanks Wayne
  12. Replies
    1,516
    Views
    334,500

    Wayne can you help me? I am having trouble with...

    Wayne can you help me? I am having trouble with my 360 reading from Helix 12 Gen 3. I purchased it in June 2019 and it has been flawless until now. The transducer is turning but it only shows a blank...
  13. Thread: Octane

    by JRBjr
    Replies
    19
    Views
    822

    The only non ethanol gas I can get is 87 octane. ...

    The only non ethanol gas I can get is 87 octane. I have had two different SHO engines and it is all that I have run since 2011. There has been no problem whatsoever. There have been a few times...
  14. Replies
    6
    Views
    345

    I have an Ultrex with I Pilot link paired with a...

    I have an Ultrex with I Pilot link paired with a Hummingbird 1199 and it works fine.
  15. Replies
    3
    Views
    178

    Thanks Wayne, I was afraid that would be the only...

    Thanks Wayne, I was afraid that would be the only solution but I am not sure it is worth paying another 265.00 to link my units. I think I will put my waypoints on an SD card and just transfer them....
  16. Replies
    3
    Views
    178

    Networking with Ultrex

    I have an 1199 at the bow and have recently paired it with an Ultrex using the Ethernet port. In order to do that, I had to disconnect from the unit at the console. My question is: Can I have both a...
  17. Replies
    3
    Views
    559

    Mine did the same thing a few years ago. One of...

    Mine did the same thing a few years ago. One of my spark plugs was cracked. It was an easy fix. I hope that yours is as well.
  18. Replies
    1
    Views
    335

    Ice chest leaking

    When I pull the plug in my ice chest my carpet in the port side rod locker gets wet. There is no crack in the fiberglass of the cooler. Does anybody know how the drain works and the big question is...
  19. Replies
    7
    Views
    2,126

    I have a 2012 Z521 and my hubs appear to be the...

    I have a 2012 Z521 and my hubs appear to be the Vault hubs rather than the Vortex ones. I think it is best to call the factory and give them your serial number to be absolutely certain as to what...
  20. Replies
    24
    Views
    2,882

    Something I've often thought about is, if I am...

    Something I've often thought about is, if I am wearing laced up hunting boots and I fall overboard will I be able to get back to the boat safely. I fish all winter in cold temps. I have a pair of...
  21. Replies
    22
    Views
    716

    I order from them all the time. They are a great...

    I order from them all the time. They are a great company with great service. Just go to their web site and get what you want.
  22. Call Ranger, they will take care of you. The same...

    Call Ranger, they will take care of you. The same thing happened to my 2012 and I called them and they told me that they received a bad batch of those U bolts and they were breaking. They will send...
  23. Replies
    5
    Views
    197

    Sorry I forgot to mention that my boat is a 2012...

    Sorry I forgot to mention that my boat is a 2012 Z521. Thanks for the advice I will get the repair kit.
  24. Replies
    5
    Views
    197

    Seat base question

    Down inside the base, at the bottom of the hole there is a plastic piece that has broken. When the post is inserted the clip locks down over it. Has anyone ever had that to happen to them and if so...
  25. Replies
    5
    Views
    1,923

    I have been running 87 octane in my 250 SHO for...

    I have been running 87 octane in my 250 SHO for the past 4 years without any problem whatsoever. I run 87 because I can get it without ethanol. My engine runs great with it.
Results 1 to 25 of 487
Page 1 of 20 1 2 3 4