Search:

Type: Posts; User: Matt Wayne

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    692

    I used the conceal kits. You have to be careful...

    I used the conceal kits. You have to be careful but it's doable. Mount them as low to the deck as you can get them (allows them to hold the rods down better)
    There is no way I would cut a hole in...
  2. Replies
    17
    Views
    646

    Try a different hub kit if you have one. I’ve...

    Try a different hub kit if you have one. I’ve had this happen and it was the insert. It didn’t matter in the smaller barrel props like the promax but a bravo or hydro would rub a little. Put in a...
  3. Replies
    8
    Views
    830

    PM sent

    PM sent
  4. Replies
    5
    Views
    266

    As a general rule if your connecting to a brass...

    As a general rule if your connecting to a brass fitting or another metallic fitting use the metal clamps. If you’re connecting to a plastic fitting use the ty raps. There is exceptions to this...
  5. Thread: Thank You!

    by Matt Wayne
    Replies
    10
    Views
    785

    I would like to know how many duckett rods they...

    I would like to know how many duckett rods they sold. Everybody I seen was carrying at least 3 around. :laugh:
  6. Thread: Rub rail

    by Matt Wayne
    Replies
    5
    Views
    258

    It will come rolled up. It’s not preformed but...

    It will come rolled up. It’s not preformed but all you have to do is sit it out in the sun to warm up and it lays on there pretty good
  7. Replies
    16
    Views
    691

    You can adjust the timing on the throttle arm. ...

    You can adjust the timing on the throttle arm. The top of it is connected to the trigger. It’s not something you want to guess at though. If you’re not familiar with how it’s done then I would...
  8. Replies
    16
    Views
    691

    I would double check the timing and make sure...

    I would double check the timing and make sure it's reaching wide open throttle. There is no way dropping the compression a little will cause you to loose 10 mph. More set back should only help top...
  9. Replies
    25
    Views
    1,298

    I ran my xrs/300xs at 3/4' above the pad when...

    I ran my xrs/300xs at 3/4' above the pad when loaded to fish. To me it had better acceleration and more lift at that height. It would run 88-90 loaded depending on fuel and livewells with 14"...
  10. Thread: xb21/225x

    by Matt Wayne
    Replies
    25
    Views
    1,049

    Yes

    Yes
  11. Replies
    12
    Views
    567

    That's what I'm putting on mine when the time...

    That's what I'm putting on mine when the time comes. I did put a set on my 2002 trailer last year and so far so good. They are an American made tire and have a higher load rating than the standard...
  12. Replies
    5
    Views
    265

    The bobs will work. Keep in mind you will need...

    The bobs will work. Keep in mind you will need two power head gaskets when using an alien cowl. It has a stainless plate that sandwiches between the power head and adapter plate.
  13. Thread: xb21/225x

    by Matt Wayne
    Replies
    25
    Views
    1,049

    I’m not sure on the hours. I hooked my lap top...

    I’m not sure on the hours. I hooked my lap top up to it and it show 40something. I’m pretty sure it’s been flashed because I believe there is more hours than that on it. I don’t believe the ecu...
  14. Thread: xb21/225x

    by Matt Wayne
    Replies
    25
    Views
    1,049

    Yes it's a short shaft. I didn't even know...

    Yes it's a short shaft. I didn't even know mercury made the 225x in a short shaft but they sure did. It's all original
  15. Thread: xb21/225x

    by Matt Wayne
    Replies
    25
    Views
    1,049

    That's pretty good. If I put this thing on there...

    That's pretty good. If I put this thing on there and it runs mid 80s loaded I may not take it back off. :laugh:
  16. Thread: xb21/225x

    by Matt Wayne
    Replies
    25
    Views
    1,049

    Current state of 260. :laugh: ...

    Current state of 260. :laugh:

    http://i63.tinypic.com/30llcer.jpg

    http://i66.tinypic.com/5vpx84.jpg

    http://i64.tinypic.com/33cvtyo.jpg
  17. Thread: xb21/225x

    by Matt Wayne
    Replies
    25
    Views
    1,049

    Who knows? I really didn't have a end goal when...

    Who knows? I really didn't have a end goal when I bought it just thought it was a neat little engine so I bought it. :laugh:
    It is a much better fit for the 2002 but I know I would miss the 260. ...
  18. Replies
    6
    Views
    322

    It came from Mercury like that. You just took...

    It came from Mercury like that. You just took the yellow cover off the end of that connector. You need to remove that connector. Press in on the tab and pull the connector straight out.
  19. Thread: xb21/225x

    by Matt Wayne
    Replies
    25
    Views
    1,049

    I got the x home but don't know when I will get...

    I got the x home but don't know when I will get time to mess with it. Still torn whether I won't to try it on the big ally or not. I think it might be a fun combo.
    It will be something different...
  20. Thread: xb21/225x

    by Matt Wayne
    Replies
    25
    Views
    1,049

    :roll:

    :roll:
  21. Thread: xb21/225x

    by Matt Wayne
    Replies
    25
    Views
    1,049

    xb21/225x

    Has anybody ran this combo? Just curious how it did.
  22. Replies
    7
    Views
    348

    Mine is mounted on the side of the jack plate on...

    Mine is mounted on the side of the jack plate on a transducershield bracket. Thought I had a pic of it but couldn't find it.
  23. Replies
    9
    Views
    372

    I believe that motor should have 143 degree...

    I believe that motor should have 143 degree t-stats and yes it it want pee at idle until the motor warms up and the t-stats open. I would definitely replace that water pressure gauge so your not...
  24. Replies
    2
    Views
    207

    Sounds like your vst is over flowing. You will...

    Sounds like your vst is over flowing. You will have to take it apart and clean or replace the float needle.
  25. Replies
    7
    Views
    290

    To answer your question. Yes you will get a solid...

    To answer your question. Yes you will get a solid alarm if your on the rev limiter and hold it there. It will even slow you down if you don’t let off the throttle.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4