Is it possible to get my 2020 SHO to be able to show more gauges on my Hummingbird Helix 7 G3N than the engine temp and RPM? What would I need to buy/install to do this? I already have the NMA2000...
Type: Posts; User: runmhard
Is it possible to get my 2020 SHO to be able to show more gauges on my Hummingbird Helix 7 G3N than the engine temp and RPM? What would I need to buy/install to do this? I already have the NMA2000...
I have a 1/2 HP electric trailer dolly that was used to move my 20 foot bass boat into and out of my garage. Forward and reverse switch. 120 volt 3 knobby pneumatic tires. Photos available. Works...
Thanks, I will check that.
[B]I just bought a 2020 ZX200 with a 200 SHO. The engine had 20 hours on it when I bought it. I put the boat in the water and ran it but the water pressure gauge does not show any water pressure. ...
I just bought a boat with networked Humminbird Helix 7 GPS G3N units at the bow and at the console. The console unit starts and the view takes up the whole height and width of the screen. The bow...
I just bought a new to me 2020 Skeeter ZX 200 with a Yamaha 200 SHO. This rig has a 23 T2 prop and my question is can you tell if the the engine has been flashed? The reason I am asking is when I...
I just finished a compression test on my 2009 200 HP Optimax SN 1B698865. The results were as follows:
Cyl 1 120
Cyl 2 120
Cyl 3 120
Cyl 4 118
Cyl 5 112
Cyl 6 102
The test was run on...
Yes I do get a the alarm when I turn the key to start the engine. I have not checked the the lower unit oil but I will. I did check the fuel and the air pressure about 3 weeks ago and they were...
I have a 2009 Mercury Optimax 200 SN 1B698865. I was running a 25 Razor Straight 3 blade prop running 5200 RPM at 64 MPH. I wanted to get the RPM up so I tried a 23 or 24 Trophy and the RPM increased...
I have a HELIX 5 CHIRP SI G2 that does not want to shut down. When I push the power button to shut the unit off, the pop up starts and counts down 3 seconds and if you don't take your finger off the...
Thanks for the help.
I have a Helix 5 CHIRP SI G2 that I connected to 2 Transducers. One is mounted on the transom and is the transducer that was supplied with the unit. The second transducer is mounted inside the hull...
I just installed a new Helix 5 CHIRP SI G2. I installed everything by the book. When the unit started the instructions indicated that the unit would start and automatically default to the...
My pontoon boat sits in the water most of the time. The algae on the toons has built up so much that I am going to have to take it out and remove it. Is a pressure washer the best way to do this? ...
I have a 2004 Honda BF 130 and the Propeller Shaft Holder is corroding to the point that it is going to have to be replaced. I do most of the work on this engine, what is involved with replacing...
I have a Razor 25 Straight on a 2009 Mercury Optimax pushing a Beeline 295 dual console. The prop shaft is 3.5 inches below the bottom of the pad and I have an 8" manual plate. The hole shot is OK...
The warning was 4 short beeps about every 2 minutes. We drained the VST to rule out the water in the gas. Low oil level and water in the gas were the two conditions that I saw would cause this...
I have a 2009 Optimax 200 with approx. 250 hours on it. A week ago while running the low oil level alarm sounded. Not being too far from the ramp we went back to the ramp and checked the oil level. ...
I have a 2004 Honda 130 and the engine oil drain bolt does not want to stay tight. I tightened the bolt when I changed the engine oil, took the boat out twice and I noticed that there was a little...
I have a 2009 Mercury Optimax 200 SN 1B698865 that started to have cooling problems after running through a patch of hydrilla. When first starting in the morning, the engine warms up to 134 deg....
I have a 2004 Honda 130. Do these engine's have poppet valves? If so, where would it be located?
I have a 2009 Mercury Optimax 200 SN 1B698865 that has a bad compressor. I understand when replacing the compressor you need to prime the oil feeding into the compressor. Is there a way to do this...
I have used Martys Marine in Osage Beach for years. Most honest and best service people on the lake. Take it there. http://www.bassboatcentral.com/boardstuff2/beers.gif
I have an 09 Optimax 200 and I just noticed that my prop shaft is bent. Is it possible to put in a new prop shaft or am I looking at a new lower unit? ...
I had this same problem. I took my trolling motor off. You will need a Phillips head screw driver and either a 7/16 or 9/16 (dont remember the size) wrench as the bolts below the deck have the...