Search:

Type: Posts; User: fklenda

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    67

    flush mount control box

    the three screws that hold the box to the face plate were missing when i took the handle of the control box off, what size and length should they be for a evinrude motor
  2. Thread: Boat pics!

    by fklenda
    Replies
    125
    Views
    149,557

    Sticky: to jwinslow13 on side panels

    to jwinslow13 on side panels
  3. Thread: Boat pics!

    by fklenda
    Replies
    125
    Views
    149,557

    Sticky: I would like to get some pics of the inside side...

    I would like to get some pics of the inside side panels. i have a 1800 xpt that i am fixing up and cant find the right one to refer to so i can rebuild the panels. thanks
  4. Replies
    3
    Views
    227

    THANK YOU VERY MUCH.

    THANK YOU VERY MUCH.
  5. Replies
    3
    Views
    227

    THE MOTOR IS A 92

    THE MOTOR IS A 92
  6. Replies
    3
    Views
    227

    THE RIGHT SPARK PLUGS TO USE

    I HAVE A EVINRUDE INTRUDER 150 SPITFIRE SERIES. FROM LOOKING AT THE CHART ON PLUGS IT SAID TO USE CHAMPION QL78C PLUG. BY TALKING TO A LOCAL BOAT PLACE THEY SAID THAT THAT PLUG IS SOMEWHAT A RARE...
  7. Replies
    12
    Views
    1,907

    evinrude intruder 150 v6 spitfire series

    evinrude intruder 150 v6 spitfire series
  8. Replies
    12
    Views
    1,907

    ok i have power now. but my bilge is not working...

    ok i have power now. but my bilge is not working it was before,i think there is a short somewhere there is one wire on the back of the switch that gets real warm i guess i need to chase that wire...
  9. Replies
    12
    Views
    1,907

    i replaced the lug on the positive side...

    i replaced the lug on the positive side cable,took my ohm meter and check the ends to the starter and i have power to the starter. then i checked the switches on the back side of them troll 1 i have...
  10. Replies
    12
    Views
    1,907

    there are two 4g ones to the motor and there are...

    there are two 4g ones to the motor and there are 2 16's also from what is labeled it says troll 2 i have some like that on my other battery that say troll 1 i do have three red switches by my battery...
  11. Replies
    12
    Views
    1,907

    changing battery

    i changed one of my batteries on my boat now nothing i hooked the wires back except the aerator and i have no dash lights no bilge pump and that worked last week no courtesy light no lighted switches...
  12. Replies
    2
    Views
    329

    thanks

    thanks
  13. Replies
    2
    Views
    329

    whats good hydrofoil for a evinrude 150

    looking for a new hydrofoil for my boat dont know what to get, dont want to drill new holes whats a good one for the least amount of money
  14. Thread: stearing

    by fklenda
    Replies
    7
    Views
    316

    stearing

    the steering on my boat is so stiff,being they dont make cajun parts where can i get a new steering setup? i have a 93 1800 xpt
  15. Thread: fuel tank

    by fklenda
    Replies
    3
    Views
    143

    i was thinking of doing what you said at the...

    i was thinking of doing what you said at the last. thanks
  16. Thread: fuel tank

    by fklenda
    Replies
    3
    Views
    143

    fuel tank

    i have a 93 1800 xpt what would be the size of the fuel tank. there is just a little over half tank in now just needing to know what mix to make to top it off.
  17. Replies
    11
    Views
    659

    weather here in kansas tight now is wet for this...

    weather here in kansas tight now is wet for this next week. thanks for getting the pics ,when ever you can get the chance would be fine. thanks
  18. Replies
    11
    Views
    659

    i have a 93 1800 xpt mine does not look as good...

    i have a 93 1800 xpt mine does not look as good yours. i also havent find much info either. iam trying to fix her up to look as good has yours. if i could ask for a pic of the inside by the throttle...
  19. Replies
    3
    Views
    181

    that is what I am thinking.

    that is what I am thinking.
  20. Thread: trailer bunks

    by fklenda
    Replies
    9
    Views
    498

    ok will do thanks

    ok will do thanks
  21. Thread: trailer bunks

    by fklenda
    Replies
    9
    Views
    498

    trailer bunks

    after looking at pro bass for bunks for my trailer, and reading the reviews i am thinking of making my own. now getting the boat up off the bunks i was thinking of using my cherry picker to lift the...
  22. Replies
    3
    Views
    181

    battery problems

    i have three batterys on my boat,they been sitting since late summer never maintained over the winter. i tried charging them only for 8 hrs should i put them on slow charge for 24 hrs and have them...
  23. Replies
    6
    Views
    234

    marinetwx same as j b weld i took the seat off...

    marinetwx same as j b weld i took the seat off and removed some carpet,there where many holes made from the past of someone drilling into the fiberglass. want to do it right or better then what was...
  24. Replies
    1
    Views
    172

    best rod holder?

    what is the best rod holder to mount on a boat for when trolling for channel so you wont loose your pole from a snag or a strike?
  25. Replies
    6
    Views
    234

    cool

    cool
Results 1 to 25 of 42
Page 1 of 2 1 2