Is 360 checked on the 3 other units on the 360 tab?
Type: Posts; User: tweakjr
Is 360 checked on the 3 other units on the 360 tab?
You could try ensuring the encrypt folder is present on both.
Temporarily turn off write-protect switch.
Just installed 2.76 and 1.170 Helix/ML software and my ML landscape image is still reversed.
I will try the solution in post #2 next time out on the water.
Kind of silly HB didn't fix in the last...
For some reason when connected through my home internet router, it forces the secure https version of the site.
If I connect through my cell provider, it does not.
Even after going back to the...
The last setting change that finally worked for me, after doing the above suggestions was go to
Settings
Site settings
scroll down to Desktop Site and turn off.
Chrome for Android
Cheers
I have a mix of Helix Gen2, Gen3, and gen4.
I experienced incessant ML freezing when I added the Gen4.
If I exclude the Gen4 from running the ML I do not get freezing(unchecked under source tab.) ...
Check your transducer selection and be sure it includes Mega 360.
Did you redo the transducer selection again after the default reset?
From what I recall, my Helix used to remember fuel used and you manually reset.
When I switched to stand alone NMEA 2k gauges for fuel management , I needed to add this memory device.
It may help...
Power button, Night mode does change the map background dark.
Do you have the ignition turned on while attempting to customize a data field for engine hours?
Can you turn AHRS back to ON after the toggle solution?
Assuming you have the Yamaha connected to NMEA2k backbone and NMEA backbone connected to Helix 9G3N via NMEA blackbox?
If you're seeing engine data on the Helix and want to customize the Data boxes,...
Yamaha connects to NMEA backplane.
NMEA backplane connects to 12v power and HB NMEA ethernet device(AS-ETH-NMEA2K)
HB NMEA ethernet device connects to HB 5 port switch.
Helix G3N connects to 5...
Sounds like you've narrowed it down to a faulty SD card.
Are the suspect cards a microSD inside an SD adapter? If so try another adapter.
You can find some free software for PC that will fully test...
In reference to post #6, I swapped back my G4N with the G3N and ran ML on both G3N's for 12 hours without one single ML freeze incident.
G4N was only used to display map/2D.
I didn't power up in...
The only way to know is to try it.
I did at one time install an 0183 to 2k converter with the hopes GPS data would be available on the 2k bus, but ended up putting a Point1 GPS puck on the NMEA2k...
In my personal experience I ran ML and mega 360 no problem for many months.
After I switched out a Gen2 to a Gen4 I started getting freezing on the gen4 when using ML and Ulterra would disconnect.
...
Curious if anyone has insight on how to manage merging ACDATA files on ZLC.
I use two Zero Line Cards on two separate units and periodically will backup the data contained in ACDATA folders.
I...
Great deduction.
I used the ML with a Gen3 Helix for many months in the fwd bow spot without freezing.
It wasn't until I swapped the Gen3 for a Gen4 that it started freezing.
I guess there will be...
I will say it's a combination issue with Gen4 Helix, MegaLive, and possibly Mega360 mix.
My system started doing the same thing when I switched out a Gen3 Helix with a Gen4 Helix at the bow, also...
Are you getting depth reading below 5mph?
If yes, then your high speed needs height adjusting or a different location.
In my case I swapped a Helix 10GG3N for a Helix 10 G4N at the same location, same cables, power wires etc.
Been using the ML on the G3N for months and didn't have the freezing issue like the G4N...
It's definitely a network reset of some sort when the ML freezes.
I'm using 2 switches and the ML and Ulterra are connected to the same front switch.
I would suspect the front switch is resetting...
Assuming there is a heading sensor installed, you can adjust HEADING OFFSET.